EDITING EN 65

 

 

Audio Dubbing (DV Deck Only)

 

 

 

 

 

● Slide the TV/CABLE/SAT/DVD switch to DVD.

 

 

 

 

 

 

 

 

 

 

 

 

 

1 Connect an audio device to the unit’s [AUDIO] input connectors
This function allows you to record new audio, without erasing the
original audio, on a DV tape that was recorded with ADV AUDIO

 

on the front panel.

 

● When using a monaural audio device, connect its AUDIO OUT
RECB set to A12BITB (A pg. 72).

 

 

connector to the [AUDIO-L]input connector on your unit.

 

 

 

 

ATTENTION:

You cannot perform Audio Dubbing on a tape that was recorded with ADV AUDIO RECB set to A16BITB (A pg. 72), on a tape that was recorded at the ALPB speed, or on a blank tape.

Your unit

 

 

 

 

Recorder

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PR +/-

A.DUB

To [AUDIO]

 

input

 

Audio cable

 

(not supplied)

 

AUDIO OUT

 

CD player, etc.

 

 

CD player, etc.

 

 

Mixer output

Audio mixer

 

Original sound

 

Your unit

[AUDIO OUT]

Recorder

2Load a Mini DV cassette with the erase protection switch set to

ARECB.

3Press DV/HDD/DVD SELECT on the unit repeatedly or DV on the remote so that the DV lamp lights up on the unit.

4Press PR +/– to select AF-1B.

5Start playback slightly before the actual point from where you wish to start dubbing.

6Press W to pause playback.7Press A.DUB to engage the audio dubbing mode.●Your unit enters the Audio Dubbing Pause mode.

●To perform Audio Dubbing with audio mixing, press AUDIO to select AL W X RB at this point. When using the DV deck as the recording deck, also make sure that AAUDIO MODEB is set to ASOUND1B (A pg. 72).

*Audio Dubbing with audio mixing is not possible if you are using a monaural audio component, or if you don’t have an audio mixer.

8Engage the audio device’s playback, then press I to start the tape in the unit. Audio dubbing starts at this point.

●To stop dubbing temporarily, press W. Press I to resume dubbing.

9Press o on the unit, then stop playback on the audio device to end the audio dubbing.

NOTES:

●Once the Audio Dubbing starts, you cannot use the other deck.

●When monitoring the audio dubbed sound on the DV deck, set AAUDIO MODEB to ASOUND2B (A pg. 72).

●Audio Dubbing is also possible with the [L-1 IN/OUT] or [L-2 IN/ DECODER] connector on the rear panel. When using these 21- pin SCART connectors, be sure to select the correct input mode (AL-1Bor AL-2B) in step 4.

●When playing back an audio dubbed Mini DV tape on the DV deck, set AAUDIO MODEB to ASOUND2B (A pg. 72).

●Audio dubbing is not possible using the [DV IN/OUT] connector.●Audio dubbing is not possible on a blank portion of the tape.

PR +/-

A.DUB

To

 

[AUDIO]

 

input