Menu Operations
1 Display the menu.
To display the MAIN MENU
\Press MENU button.
To display the SET-UP MENU
\Press 
button while holding 
button.
MAIN MENU
Selected item 
Operation guide
Selected item
Operation guide 
2 Press 
buttons to select an item, then press button.
•For some items, adjustments will be made by
pressing .
Ex.: When “MARKER” in the MAIN
MENU is selected
3 Press 
buttons to select an item,
then press 
buttons to make adjustments.
4 Press MENU button to return to the previous menu.
•Pressing the button again finishes the menu operation.
Audio Channel Selection
Select audio channels emitted from the speakers (L/R) and the AUDIO ASSIGN (MONITOR OUT) (OUT1(L)/OUT2(R)) terminals, when EMBEDDED AUDIO signals come in to the E. AUDIO HD/SD SDI terminal (IN1 or IN2) and SDI input (1 or 2) is selected.
•You have to choose a group of selectable audio channels before the channel selection (☞ “E.AUDIO GROUP” in “AUDIO SETTING” on page 12).
1 Press or button when a menu is not displayed.
The screen for audio channel selection is displayed.
•The screen for audio channel selection automatically disappears in about 30 seconds after the previous operation.
Audio channel selection screen
Selected item
2 Press 
buttons to select the left (L ch) or right (R ch).
3 Press 
buttons to select an audio channel.
•Each time you press the button, the audio channel changes according to the settings of “E.AUDIO GROUP” (☞ “NOTE” on page 12).
4 Press MENU button.
The screen for audio channel selection disappears.
•The setting is memorized for each input (SDI 1 and SDI 2).
On the Information Display
The monitor displays the information below.
•Make the setting to display/hide each information using the MENU with the exception of 5, controlled with a button.
•Select the position of the information display (☞ “POSITION” in “INFORMATION” on page 15).
1Audio level meter
•Not displayed when “LEVEL METER ch” is set to “OFF.” (☞ “AUDIO SETTING” on page 12)
2Signal format
•Displayed when “STATUS DISPLAY” is set to “ON.” (☞ “INFORMATION” on page 15)
•For the contents displayed, see “On the signal format” below and “Available signals” on page 9.
3Source name assigned in “CHARACTER SET.”
•Displayed when “SOURCE ID” is set to “ON.”
•Displayed in large letters when “STATUS DISPLAY” is set to “OFF” or “AUTO.”
☞“INFORMATION” on page 15
4 CRC error indication
• Displayed when “CRC ERROR” is set to “ON.” (☞ “INFORMATION” on page 15)
• A red square is displayed when an error occurs.
5 Time code
• When the input signal includes no time code, “TC –
☞“ r T.C. (time code) button/lamp” on page 6
•When any information of 1, 2, 3, or 4 above is displayed while signals come in from equipment other than a computer, the picture is displayed without overlapping the information display area.
However, the information display will overlap with the picture when...
–displaying the picture with higher resolution than the resolution of the panel in 1:1 mode.
–“SD4:3 LARGE” setting is “ON.”
(☞ “FUNCTION SETTING” on page 14).
On the Status Display
If you press the INPUT SELECT button of the current input, the status of the input signal and setting of muting are displayed for about 3 seconds.
•Make the setting to display/hide the status in “STATUS DISPLAY” of the “INFORMATION” (☞ page 15).
•When “STATUS DISPLAY” is set to “AUTO” or “ON,” the status below is also displayed in the following cases:
–When you change the input
–When the signal condition of the current input changes
–When you turn on the monitor
•When “STATUS DISPLAY” is set to “ON,” the signal format will remain displayed 3 seconds after the status is displayed.
1Signal format
•For the contents displayed, see “On the signal format” below and “Available signals” on page 9.
2Signal format of DVI input or setting of “COMPO./RGB SEL.”
☞ “DVI INPUT SEL.” or “COMPO./RGB SEL.” on page 10
3Displayed when “SYNC INPUT SEL.” is set to “EXT.” (external synchronization)
☞ “ SYNC FUNCTION” on page 13
4Setting of “MUTING”
•Displayed only when muting is activated. ☞ “ 4 MUTING button” on page 6
On the signal format
The following messages appear depending on the type of input signals and their conditions.
When a | “*” (at the end of | |
with HDCP is input | the indication) | |
When no video signal comes in | “NO SYNC” | |
When a noncompliant video | “Out of range” | |
signal comes in | ||
| ||
When “COLOR SYSTEM” (☞ |
| |
“FUNCTION SETTING” on | “OTHERS” | |
page 14) is set to “AUTO” and | ||
the noncompliant composite |
| |
video signals come in |
|
7
