Menu Configuration—SET-UP MENU
For the operation procedure, see page 7.
Operation guide
Shows the buttons for each operation.
• The menu automatically disappears in about 30 seconds after the previous operation.
• Some items may not appear on the menu depending on the input or the input signal.
• The items controlled by the MAKE system do not appear on the menu.
NOTE
Settings of “sub menu POSI.”
The setting values and features are as follows.
LOWER1: Displays the current setting and adjustment bar at the lower part of the screen.
UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.
LOWER2: Displays the current setting at the lower part of the screen.
UPPER2: Displays the current setting at the upper part of the screen.
• The adjustment bar is not displayed for some items.
Settings of “SD4:3 LARGE”
The setting values and features are as follows.
OFF: Fit the vertical picture size into the pixel numbers of the monitor display.
ON: Fit the vertical picture size into that of the monitor display.
14
FUNCTION SETTING
Setting for the sub menu display, color system, color of the tally lamp and the picture size.
Item | To do | Setting value |
sub menu POSI. | Select the contents and displaying position of “sub menu.” | ☞ “NOTE” |
COLOR | Select the color system. | AUTO, NTSC, PAL |
SYSTEM | • If the picture is unstable with “AUTO,” select “PAL” or “NTSC.” |
|
TALLY SELECT | Select the color of the tally lamp. | GREEN, RED |
SD4:3 LARGE | Change the picture size of 4:3 format signal. | ☞ “NOTE” |
PICTURE SUB ADJ.
Adjusts the standard level for the picture adjustment and selects the
Item | To do | Setting value |
CONTRAST*1 | Adjust the standard level for the contrast adjusted | |
| with CONTRAST knob on the front panel. |
|
BRIGHT*1 | Adjust the standard level for the brightness | |
| adjusted with BRIGHT knob on the front panel. |
|
CHROMA*1 | Adjust the standard level for the chroma adjusted | |
| with CHROMA knob on the front panel. |
|
PHASE*1 | Adjust the standard level for the phase adjusted | |
| with PHASE knob on the front panel. |
|
NTSC SETUP | Select the | 00 (compliant with 0% |
|
| with 7.5% |
COMPO. | Select the level of the analog component signal | B75 (compliant with BetacamVTR 7.5% |
LEVEL | (480i and 576i only). | signal), B00 (compliant with BetacamVTR 0% set- |
|
| up signal), SMPTE (compliant with M2VTR signals) |
sub menu | Display the sub menu which enables you to adjust | the items in “PICTURE SUB ADJ.” while viewing the |
| actual picture. |
|
reset | Restore the default settings for all the items in “PICTURE SUB ADJ.” | |
*1 Memorized for each input.
SIZE/POSI. ADJ.
Adjusts the size and position of the picture.
Item | To do | Setting value |
H SIZE*2 | Adjust the horizontal picture size. |
|
H POSITION*2 | Adjust the horizontal picture position. | Setting value varies depending on |
V SIZE*2 | Adjust the vertical picture size. | the signals. |
V POSITION*2 | Adjust the vertical picture position. |
|
sub menu | Display the sub menu which enables you to adjust the items of | “SIZE/POSI. ADJ.” while viewing the |
| actual picture. |
|
reset | Restore the default settings for all the items in “SIZE/POSI. ADJ.” | |
*2 Memorized for each signal format.
WHITE BALANCE SET.
Selects the color temperature and adjusts the drive level and cutoff point of each color (R/G/B).
Item | To do | Setting value |
COLOR TEMP. | Select the color temperature. | 9300K, 6500K, USER |
R DRIVE, G DRIVE, | Adjust the drive level of each color (red, green, and blue). | MIN – 000 – MAX (in 256 grades) |
B DRIVE*3 |
|
|
R CUT OFF, G CUT | Adjust the cutoff point of each color (red, green, and blue). | MIN – 000 – MAX (in 256 grades) |
OFF, B CUT OFF*3 |
|
|
sub menu | Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while | |
| viewing the actual picture. |
|
reset | Restore the default settings for the drive levels and cutoff points of the selected color | |
| temperature. |
|
*3 Memorized for each color temperature.
