Parts list for installation and connection

A

B

C

D

Control panelSleeveTrim plate

Power cord

 

 

G

 

 

 

 

E

 

Mounting bolt—

 

I

J

K

F

M4 x 5 mm (M4 x 1/4");

H

HandlesRemote controller

Battery

Washer (ø5)
Lock nut (M5)M5 x 12.5 mm (M5 x 1/2")Rubber cushion

 

 

 

INSTALLATION

If you are not sure how to install this unit correctly, consult your JVC car audio dealer.

In dash-mounting

 

Removing the unit

 

 

 

Before removing the unit, release the rear section.When you stand the unit, be careful not to damage the fuse on the rear.Do the required electrical connections.Bend the appropriate tabs to hold the sleeve firmly in place.

INSTALLATION / CONNECTION

When using the optional stay
Fire wall

Stay (option)

DashboardScrew (option)Install the unit at an angle of less than 30˚.
When installing the unit without using the sleeve

In a Toyota car for example, first remove the car radio and install the unit in its place.

 

Flat type screws—M5 ⋅ 8 mm (M5 ⋅ 3/8")*

* Not supplied for this unit.

Bracket*

 

Flat type screws

 

—M5 ⋅ 8 mm (M5 ⋅ 3/8")*

 

Pocket

 

Bracket*

 

ELECTRICAL CONNECTIONS

Make sure to disconnect the battery’s negative terminal.
• Be sure to ground this unit to the car’s chassis again after installation.

 

Note:
High

 

It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the

 

maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page “General setting — PSM“ of the INSTRUCTIONS.).

Heat sink

 

 

 

Typical connections
Rear line outRear ground terminal

 

Antenna

 

 

15 A fuse
terminal

 

 

 

 

 

 

 

 

 

 

Ignition switch

Connect only the front speakers if your

BlackTo the metallic body

 

or chassis of the car

speaker system is two-speaker system.

 

 

White with black stripe

 

To a live terminal in the
Yellow *2fuse block connecting to the

 

 

 

 

 

 

 

car battery (bypassing the
Front speaker (left)White

 

 

ignition switch) (constant

 

 

12 V)

 

 

 

 

Gray with black stripe

 

Fuse block
RedTo an accessory terminal in

 

 

 

Front speaker (right)Gray

 

 

the fuse block

 

 

 

Green with black stripeBlue with white
stripeTo the remote lead of other

 

 

 

 

 

 

equipment or automatic antenna if

 

 

 

 

Rear speaker (left)Green

 

 

any (200 mA max.)

 

 

 

Purple with black stripe

 

 

Rear speaker (right)Purple

 

 

 

Connecting the external amplifier or subwoofer

 

 

Remote leadY-connector *1
Set “L/O MODE” to “REAR”

 

Remote lead (blue with white stripe)

 

 

 

(See “General settings—PSM.”)

 

 

To the remote lead of other equipment

You can connect a power amplifier for

 

 

 

 

or automatic antenna if any
rear speakers.

 

 

 

 

 

JVC Amplifier

 

 

 

Rear

 

 

 

speakers

 

Right

 

 

 

 

Front speakers
Set “L/O MODE” to “WOOFER”

 

Left

 

 

 

(See “General settings—PSM.”)

*1

Not supplied for this unit.

 

You can also connect a subwoofer to

*2

Before checking the operation of this unit prior to installation, this

the REAR LINE OUT terminals.

 

lead must be connected, otherwise the power cannot be turned on.

 

 

 

*3

Firmly attach the ground wire to the metallic body or to the chassis

JVC Amplifier

or

of the car—to the place uncoated with paint (if coated with paint,

 

remove the paint before attaching the wire). Failure to do so may

Subwoofer

 

 

cause damage to the unit.

 

 

 

 

 

*4

Signal cord (not supplied for this unit)
PRECAUTIONS on power supply and speaker connections
4 – EN