Parts list for installation and connection
A | B | C | D |
Control panel | Sleeve | Trim plate | Power cord |
|
| G |
|
|
|
| |
E |
| Mounting bolt— |
| I | J | K | |
F | M4 x 5 mm (M4 x 1/4"); | H | Handles | Remote controller | Battery | ||
Washer (ø5) | |||||||
Lock nut (M5) | M5 x 12.5 mm (M5 x 1/2") | Rubber cushion |
|
|
|
INSTALLATION
If you are not sure how to install this unit correctly, consult your JVC car audio dealer.
In |
| Removing the unit |
|
|
|
INSTALLATION / CONNECTION
When using the optional stay
Fire wall | Stay (option) |
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place. |
|
Flat type | * Not supplied for this unit. |
Bracket* |
|
Flat type screws |
|
| |
| |
Bracket* |
|
ELECTRICAL CONNECTIONS
Make sure to disconnect the battery’s negative terminal.• Be sure to ground this unit to the car’s chassis again after installation. |
|
Note: | High |
| |
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the |
|
maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page “General setting — PSM“ of the INSTRUCTIONS.). | Heat sink |
|
|
| Typical connections | ||
Rear line out | Rear ground terminal |
| |||
Antenna |
|
| 15 A fuse | ||
terminal |
|
| |||
|
|
|
| ||
|
|
|
| Ignition switch | |
Connect only the front speakers if your | Black | To the metallic body | |||
| or chassis of the car | ||||
speaker system is |
|
| |||
White with black stripe |
| To a live terminal in the | |||
Yellow *2 | fuse block connecting to the | ||||
|
|
| |||
|
|
|
| car battery (bypassing the | |
Front speaker (left) | White |
|
| ignition switch) (constant | |
|
| 12 V) | |||
|
|
|
| ||
Gray with black stripe |
| Fuse block | |||
Red | To an accessory terminal in | ||||
|
|
| |||
Front speaker (right) | Gray |
|
| the fuse block | |
|
|
| |||
Green with black stripe | Blue with white | ||||
stripe | To the remote lead of other | ||||
|
|
| |||
|
|
| equipment or automatic antenna if | ||
|
|
|
| ||
Rear speaker (left) | Green |
|
| any (200 mA max.) | |
|
|
| |||
Purple with black stripe |
|
| |||
Rear speaker (right) | Purple |
|
|
|
Connecting the external amplifier or subwoofer
|
| Remote lead | |
Set “L/O MODE” to “REAR” |
| Remote lead (blue with white stripe) | |
|
|
| |
(See “General |
|
| To the remote lead of other equipment |
You can connect a power amplifier for |
|
| |
|
| or automatic antenna if any | |
rear speakers. |
|
| |
|
|
| |
JVC Amplifier |
|
|
|
Rear |
|
|
|
speakers |
| Right |
|
|
|
| Front speakers |
Set “L/O MODE” to “WOOFER” |
| Left | |
|
|
| |
(See “General | *1 | Not supplied for this unit. |
|
You can also connect a subwoofer to | *2 | Before checking the operation of this unit prior to installation, this | |
the REAR LINE OUT terminals. |
| lead must be connected, otherwise the power cannot be turned on. | |
|
| ||
| *3 | Firmly attach the ground wire to the metallic body or to the chassis | |
JVC Amplifier | or | of the | |
| remove the paint before attaching the wire). Failure to do so may | ||
Subwoofer |
| ||
| cause damage to the unit. |
| |
|
|
| |
| *4 | Signal cord (not supplied for this unit) |