EDITING EN 43

Select Scenes

NOTES:

 

PAUSE

 

PLAY

CANCEL

 

EDIT IN/OUT

R.A.EDIT

FADE

ON/OFF

EFFECT

VCR REC STBY

6 Press PLAY (U) and then press R.A.EDIT ON/OFF on the remote control.

● The Random Assemble Editing

● When choosing a scene, set Edit-In and Edit-Out points so

that there is a relatively large difference between them.

● If the search time for an in-point exceeds 5 minutes, the

recording deck’s Record-Standby mode will be cancelled

and editing will not take place.

● If there are blank portions before or after the Edit-In and

Edit-Out points, a blue screen may be included in the edited

version.

● Turning off the camcorder’s power erases all registered

Edit-In and Edit-Out points.

● If you select Sepia or Monotone mode from Program AE

with special effects, you cannot use the Dissolve or Black &

White Fader. In this case the Dissolve or Black & White

Menu appears.

Selected parameter

indicator begins blinking. Once the next Edit-In point is

registered, the effect is turned off. To combine these

7 If using a Wipe/Fader at the

 

 

 

 

 

 

 

 

I N

OUT MODE

beginning of the scene, press

1 – –

– – : – –

~

 

 

2

 

 

~

 

 

FADE on the remote control.

3

 

 

~

 

 

4

 

 

~

 

 

● Cycle through the effects by

5

 

 

~

 

 

pressing repeatedly, and stop

6

 

 

~

 

 

7

 

 

~

 

 

when the one you want is

8

 

 

~

 

 

 

T I ME

CODE

– – : – –

 

 

displayed.

 

TOTAL

00 : 00

 

 

●You cannot use a Picture Wipe/ Dissolve at the beginning of Program 1.

8 At the beginning of the scene, press EDIT IN/OUT on the remote control. The Edit-In position appears in the Random Assemble Editing Menu.

9 At the end of the scene, press EDIT IN/OUT. The Edit- Out position appears in the Random Assemble Editing Menu.

10 If using a Wipe/Fader at the end of the scene, press FADE.

●Cycle through the effects by pressing repeatedly, and stop when the one you want is displayed.

●If you select a Wipe/Fader effect for an Edit-Out point, the effect is automatically applied to the following Edit-In point.

●You cannot use a Picture Wipe/Dissolve at the end of the last scene.

●When you use Fader/Wipe effects, that time is included in the total time (this does not apply to Picture Wipe/Dissolve).

11 If using Playback Special Effects, press EFFECT. ( pg. 20)

12 Repeat steps 8 through 11 to register additional scenes.

●To change previously registered points, press CANCEL on the remote control. The registered points disappear, one at a time, from the most recently registered point.

●If you are not using Wipe/Fader or Program AE with special effects, repeat steps 8 and 9 only.

effects, use Sepia or Monotone during recording, then use

the Dissolve or Black & White Fader during Random

Assemble Editing.

● It is not possible to use Wipe/Fader effects and Program AE

with special effects during Random Assemble Editing using

a DV cable.

Picture Wipe And Dissolve Menu (available only for Random Assemble Editing)

You can use not only the wipe/fader effects on page 34 but also the picture wipe and dissolve effects below.

DISSOLVE: The new scene gradually appears as the old one gradually disappears.

WIPE–CORNER: The new scene wipes in over the previous one from the upper right corner to the lower left corner.

WIPE–WINDOW: The next scene gradually wipes in from the centre of the screen toward the corners, covering the previous scene.

WIPE–SLIDE: The next scene gradually wipes in over the previous one from right to left.

WIPE–DOOR: The previous scene wipes out from the centre to the right and left, like a door being pushed open to reveal the next scene.

WIPE–SCROLL: The new scene wipes in over the last one from the bottom of the screen to the top.

WIPE–SHUTTER: The new scene wipes in over the previous one from the centre toward the top and bottom of the screen.