EN 73

33.

Colored bright spots appear all

33.

•The LCD monitor and the

33.

 

 

 

 

over the LCD monitor or the

 

viewfinder are made with

 

 

 

 

 

viewfinder.

 

high-precision technology.

 

 

 

 

 

 

 

However, black spots or

 

 

 

 

 

 

 

bright spots of light (red,

 

 

 

 

 

 

 

green or blue) may appear

 

—

 

 

 

 

 

constantly on the LCD

 

 

 

 

 

 

monitor or the viewfinder.

 

 

 

 

 

 

 

These spots are not recorded

 

 

 

 

 

 

 

on the tape. This is not due to

 

 

 

 

 

 

 

any defect of the unit.

 

 

 

 

 

 

 

(Effective dots: more than

 

 

 

 

 

 

 

99.99 %)

 

 

 

 

 

 

 

 

 

 

 

 

34.

The indicators and the image

34.

•This may occur when the

34.

 

 

 

 

color on the LCD monitor are

 

surface or the edge of the

 

—

 

 

 

not clear.

 

LCD monitor is pressed.

 

 

 

 

 

 

 

 

 

 

 

35.

The cassette will not load

35.

•The battery’s charge is low.

35. •Install a fully charged battery.

 

 

 

properly.

 

 

 

( pg. 10, 11)

 

 

 

 

 

 

 

 

 

 

36.

The memory card cannot be

36.

—

36.

•Push in the memory card a

 

 

 

removed from the camcorder.

 

 

few more times. ( pg. 16)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

37.

Picture does not appear on the

37.

•The viewfinder is pulled out

37.

•Push the viewfinder back in

 

 

 

LCD monitor.

 

and “PRIORITY” is set to

 

or set “PRIORITY” to “LCD”.

 

 

 

 

 

“FINDER”.

 

( pg. 12, 31, 38)

 

 

 

 

 

•The LCD monitor’s brightness

 

•Adjust the brightness of the

 

 

 

 

 

setting is too dark.

 

LCD monitor. ( pg. 13)

 

 

 

 

 

 

 

•If the monitor is tilted

 

 

 

 

 

 

 

upward 180 degrees, open

 

 

 

 

 

 

 

the monitor fully. ( pg. 12)

 

 

 

 

 

 

 

 

 

 

38.

Images on the LCD monitor

38.

•The speaker volume is too

38.

•Turn the speaker volume

 

 

 

are jittery.

 

great.

 

down. ( pg. 20)

 

 

 

 

 

 

 

 

 

 

39.

The LCD monitor, the

39.

 

39.

•Wipe them gently with soft

 

 

 

viewfinder and the lens have

 

 

 

cloth. Wiping strongly can

 

 

 

become dirty (ex. fingerprints).

 

—

 

cause damage. ( pg. 77) To

 

 

 

 

 

 

clean the viewfinder, please

 

 

 

 

 

 

 

 

 

 

 

 

 

 

consult your nearest JVC

 

 

 

 

 

 

 

dealer.

REFERENCES

 

 

 

 

 

 

40.

Time code does not appear.

40.

•“TIME CODE” is set to

40.

•Set “TIME CODE” to “ON”.

 

 

 

 

 

“OFF”.

 

( pg. 31, 38, 41)

 

 

 

 

 

 

 

 

 

 

41.

An error indication (E01, E02

41.

•A malfunction of some kind

41.

• pg. 85.

 

 

 

or E06) appears.

 

has occured. In this case the

 

 

 

 

 

 

 

camcorder’s functions

 

 

 

 

 

 

 

become unusable.

 

 

 

 

 

 

 

 

 

 

 

 

42.

An error indication (E03 or

42.

•A malfunction of some kind

42.

• pg. 85.

 

 

 

E04) appears.

 

has occured. In this case the

 

 

 

 

 

 

 

camcorder’s functions

 

 

 

 

 

 

 

become unusable.

 

 

 

 

 

 

 

 

 

 

 

 

43.

The remote control does not

43.

•“REMOTE” is set to “OFF”.

43.

•Set “REMOTE” to “ON”.

 

 

 

work.

 

•The remote control does not

 

( pg. 31, 37)

 

 

 

 

 

point at the remote sensor.

 

•Point at the remote sensor.

 

 

 

 

 

•The remote control batteries

 

( pg. 56)

 

 

 

 

 

are exhausted.

 

•Replace the batteries with

 

 

 

 

 

 

 

fresh ones. ( pg. 56)