![](/images/new-backgrounds/1140862/14086291x1.webp)
46![](/images/new-backgrounds/1140862/14086291xi2.webp)
EN![](/images/new-backgrounds/1140862/14086291xi4.webp)
![](/images/new-backgrounds/1140862/14086291xi5.webp)
![](/images/new-backgrounds/1140862/14086291xi6.webp)
![](/images/new-backgrounds/1140862/14086291xi7.webp)
![](/images/new-backgrounds/1140862/14086291xi8.webp)
![](/images/new-backgrounds/1140862/14086291xi9.webp)
![](/images/new-backgrounds/1140862/14086291xi10.webp)
![](/images/new-backgrounds/1140862/14086291xi11.webp)
![](/images/new-backgrounds/1140862/14086291xi12.webp)
![](/images/new-backgrounds/1140862/14086291xi13.webp)
![](/images/new-backgrounds/1140862/14086291xi14.webp)
USING![](/images/new-backgrounds/1140862/14086291xi15.webp)
![](/images/new-backgrounds/1140862/14086291xi16.webp)
THE![](/images/new-backgrounds/1140862/14086291xi18.webp)
REMOTE![](/images/new-backgrounds/1140862/14086291xi20.webp)
CONTROL![](/images/new-backgrounds/1140862/14086291xi22.webp)
UNIT
![](/images/new-backgrounds/1140862/14086291xi24.webp)
(cont.)![](/images/new-backgrounds/1140862/14086291xi26.webp)
![](/images/new-backgrounds/1140862/14086291xi27.webp)
Remote sensor
Power Switch
REW | FF | |
PAUSE | ||
PLAY | ||
CANCEL | ||
IN/OUT | ||
ON/OFF | ||
|
|
| |
|
| (optional) |
| I N | OUT |
1 | 0 : 0 0 : 2 5 | - |
2 |
|
|
3 |
|
|
4 |
|
|
5 |
|
|
6 |
|
|
7 |
|
|
8 |
| 0 : 0 0 : 2 5 |
COUNTER | ||
TOTAL | 0 : 0 0 : 0 0 | |
| I N | OUT |
1 | 0 : 0 0 : 2 5 | 0 : 0 1 : 0 5 |
2 | 0 : 0 3 : 1 8 | 0 : 0 3 : 3 1 |
3 | 0 : 0 2 : 3 3 | 0 : 0 2 : 5 3 |
4 | 0 : 0 4 : 1 1 | - |
5 |
|
|
6 |
|
|
7 |
|
|
8 |
| 0 : 0 4 : 1 1 |
COUNTER | ||
TOTAL | 0 : 0 1 : 1 3 |
SELECT SCENES
4 Point the remote control at the camcorder’s remote sensor. Press PLAY, then press ON/OFF on the remote control. The R.A. Edit counter display appears.
5 Press REW or FF to locate the beginning of the scene you want, then press IN/OUT to register that point. The data appears under “IN” on the display.
6 Press REW or FF to locate the end of the scene and press IN/OUT to register it.
•The data appears under “OUT” on the display. •The total time of the registered scene(s) is displayed
at the bottom of the screen.
7 Repeat steps 5 and 6 for each additional scene (as many as 8).
8 To make corrections, press CANCEL during steps 5 and 6 to erase the most recently registered point.
NOTES:
●There must be at least one second between an
●To ensure correct operation, there should be at least
15 seconds between an
●Blank portions of a tape cannot be registered as
●If it takes more than 5 minutes to search for an
●Pressing ON/OFF clears all in- and
●Leave a small margin for error around each
●Turning off the camcorder’s power erases all registered in- and