EDITING

 

EN 49

● Never connect the USB cable and the DV

 

 

Insert Editing

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cable simultaneously to the camcorder.

 

 

 

 

 

 

 

 

 

 

 

Connect only the cable you wish to use to the

 

 

 

 

 

 

 

 

 

 

 

 

You can record a new scene into a previously

camcorder.

● When using a DV cable, be sure to use the

recorded tape, replacing a section of the original

optional JVC VC-VDV206U or VC-VDV204U DV

recording with minimal picture distortion at the in

cable depending on the type of DV connector

and outpoints. The original audio remains

 

 

(4 or 6 pins) on the PC.

unchanged.

 

 

 

 

 

 

 

 

 

● If the PC connected to the camcorder via the USB

● Use the provided remote control.

 

 

cable is not powered, the camcorder does not

NOTES:

 

 

 

 

 

 

 

 

 

enter the USB mode.

 

 

 

 

 

 

 

 

 

● Before performing the following steps, make sure

● The date/time information cannot be captured into

the PC.

 

that “TIME CODE” is set to “ON” in CAMERA

 

DISPLAY and VIDEO DISPLAY menus.

 

 

● Refer to the instruction manuals of the PC and

 

 

 

 

( pg. 33, 36, 38)

 

 

 

 

 

 

 

 

 

Software.

 

 

 

 

 

 

 

 

 

 

● Insert editing is not possible on a tape recorded in

● The still images can also be transferred to a PC

 

the LP mode or on a blank portion of a tape.

with a DV connector-equipped capture board.

 

1 Play back the

 

 

 

 

 

 

 

 

 

● The system may not work properly depending on

 

 

 

 

 

 

 

 

 

the PC or capture board you are using.

tape, locate the edit-

 

 

 

 

 

 

 

START/

 

 

 

 

 

 

 

 

 

out point and press

 

 

 

 

 

 

 

STOP

 

PAUSE (9). Confirm

REW

 

 

 

 

 

 

PAUSE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the time code at this

 

 

 

 

 

 

 

INSERT

 

 

 

 

 

 

STOP

 

point. ( pg. 19)

 

 

 

 

 

 

 

 

 

 

 

 

2 Press REW (3)

until the edit-in point is located, then press PAUSE (9).

3 Press and hold INSERT (I) on the remote control, then press PAUSE (9). The “9I” indicator and the time code (min.:sec.) appear and the camcorder enters insert-pause mode.

4 Press START/STOP to begin editing.

● Confirm the insert at the time code you checked in step 1.

● To pause editing, press START/STOP. Press it again to resume editing.

5 To end insert editing, press START/STOP, then STOP (8).

NOTES:

● Program AE and special effects ( pg. 44, 45) can be used to spice up the scenes being edited during insert editing.

● During insert editing, the date and time information changes.

● If you perform insert editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas.

● During insert editing, when the tape moves to scenes recorded in the LP mode or a blank portion, insert editing stops. ( pg. 55)