82 EN |
| TROUBLESHOOTING (cont.) | |
VIDEO NAVIGATION |
|
| |
| SYMPTOM | POSSIBLE CAUSE | CORRECTIVE ACTION |
2. | The VCR cannot search for the | • Two (or more) tape numbers are | Video Navigation cannot work |
| desired program. | recorded on one tape. | correctly on a tape if it has more than |
|
|
| one tape number. If this happens, |
|
|
| |
|
| • The inserted program is not | eject it, and try it again. |
|
| recorded on this VCR. | It is impossible to search the desired |
|
|
| program which is not recorded on |
|
|
| this VCR using Video Navigation. |
|
|
|
|
3. | “MEMORY FULL” appears on the | • The VCR’s memory for Video | Check the remaining memory |
| screen when you try to start | Navigation is fully recorded. | (A page 61). If it is full, delete |
| recording. |
| unnecessary Video Navigation |
|
|
| information (A pages 60, 61). |
|
|
|
|
4. | The information data for Video | • The VCR’s memory for Video | Check the remaining memory |
| Navigation is not registered. | Navigation is fully recorded. | (A page 61). If it is full, delete |
|
|
| unnecessary Video Navigation |
|
|
| information (A pages 60, 61). |
|
| • “NAVIGATION” is set to “OFF”. | Set “NAVIGATION” to “ON” |
|
|
| (A page 52). |
|
| • The recording time is not enough. | For details on the recording time for |
|
|
| Video Navigation, refer to ‘NOTES’ |
|
|
| on page 51. |
|
|
| |
OTHER PROBLEMS |
|
| |
| SYMPTOM | POSSIBLE CAUSE | CORRECTIVE ACTION |
1. | When scanning channels, some | • Those channels have been preset to | If you need the skipped channels, |
| of them are skipped over. | be skipped. | restore them (A page 21). |
|
|
|
|
2. | The channel cannot be changed. | • Recording is in progress. | Press [PAUSE (W)] to pause the |
|
|
| recording, change channels, then |
|
|
| press [PLAY (I)] to resume recording. |
|
|
|
|
3. | The Remote will not operate your | • The brand codes are set incorrectly. | Reset the correct brand codes |
| TV or cable box or DBS receiver. |
| (A pages 76, 77). |
|
|
|
|
4. | Even though Auto or Semiauto | • The clock setting data received | Select a different host channel during |
| Clock Set has been performed, | from the host channel is incorrect. | Semiauto Clock Set (A page 18), or |
| the clock is incorrect. |
| perform Manual Clock Set |
|
|
| (A page 19). |
|
|
|
|
5. | “PM” blinks on the front display | • The VCR do not work properly. | Unplug the AC power plug once, |
| panel. |
| then plug it again. |
|
|
|
|
6. | The subtitles and the menu screen | • The subtitle display on the TV is set | Set it to off. |
| are overlapped. | to on. |
|
|
|
|
|
7. | The subtitles cannot be displayed. | • You are viewing the program in EE | Make use of the analog connection |
|
| mode through the HDMI | (Component Video, |
|
| connection. | Video), and set “TV OUTPUT 2” to |
|
|
| “ALLto480i” (A page 65). However, |
|
|
| if the picture is of 480p image format, |
|
|
| the subtitles cannot be displayed. |
|
|
|
|