34
EN
T
R
OUBLESHOOTING
(cont.)
| RECORDING |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
| SYMPTOM |
| POSSIBLE CAUSE |
|
| CORRECTIVE ACTION |
|
| 1. | Recording cannot be started. |
| ● There is no cassette loaded, or the |
| Insert a cassette, or using adhesive |
| |
|
|
|
| cassette loaded has had its Record |
| tape, reseal the slot where the tab |
| |
|
|
|
| Safety tab removed. |
| was removed. |
| |
|
|
|
|
|
|
|
|
|
| 2. | TV broadcasts cannot be recorded. |
| ● “AU” has been selected as the input |
| Set to the desired channel. |
| |
|
|
|
| mode. |
|
|
| |
|
|
|
|
|
|
|
|
|
| 3. |
| ● The source (another video recorder, |
| Confirm that the source is properly |
| ||
|
|
|
| camcorder) has not been properly |
| connected. |
| |
|
|
|
| connected. |
|
|
| |
|
|
|
| ● All necessary power switches have |
| Confirm that all units’ power switches |
| |
|
|
|
| not been turned on. |
| are turned on. |
| |
|
|
|
| ● The input mode is not correct. |
| Set the input mode to “AU”. |
| |
|
|
|
|
|
|
|
|
|
| 4. | Camcorder recording is not |
| ● The camcorder has not been |
| Confirm that the camcorder is |
| |
|
| possible. |
| properly connected. |
| properly connected. |
| |
|
|
|
| ● The input mode is not correct. |
| Set the input mode to “AU”. |
| |
|
|
|
|
|
|
|
| |
| TIMER RECORDING |
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
|
| SYMPTOM |
| POSSIBLE CAUSE |
| CORRECTIVE ACTION |
| |
| 1. | Timer recording won’t work. |
| ● The clock and/or the timer have |
|
| ||
|
|
|
| been set incorrectly. |
| settings. |
| |
|
|
|
| ● The timer is not engaged. |
| Press TIMER and confirm that “ä“ is |
| |
|
|
|
|
|
|
| displayed on the display panel. |
|
|
|
|
|
|
|
|
| |
| 2. |
| ● Timer recording is in progress. |
| Timer programming can’t be |
| ||
|
| not possible. |
|
|
|
| performed while a timer recording is |
|
|
|
|
|
|
|
| in progress. Wait until it finishes. |
|
|
|
|
|
|
|
|
| |
| 3. | “ä“ and “]“ on the display |
| ● The timer is engaged but there’s no |
| Load a cassette with the Record |
| |
|
| panel won’t stop blinking. |
| cassette loaded. |
| Safety tab intact, or cover the hole |
| |
|
|
|
|
|
|
| using adhesive tape. |
|
|
|
|
|
|
|
|
| |
| 4. | The cassette is automatically |
| ● The loaded cassette has had its |
| Remove the cassette and cover the |
| |
|
| ejected, and “ä“ and “]“ on the |
| Record Safety tab removed. |
| hole with adhesive tape, or insert a |
| |
|
| display panel won’t stop blinking. |
|
|
|
| cassette with the Record Safety tab |
|
|
|
|
|
|
|
| intact. |
|
|
|
|
|
|
|
|
| |
| 5. | “ä“ blinks for 10 seconds and the |
| ● TIMER has been pressed when there |
| Check the programmed data and re- |
| |
|
| Timer mode is disengaged. |
| are no programs in memory, or the |
| program as necessary, then press |
| |
|
|
|
| timer record information has been |
| TIMER again. |
| |
|
|
|
| programmed incorrectly. |
|
|
| |
|
|
|
|
|
|
|
| |
| 6. | The cassette is automatically |
| ● The end of the tape was reached |
| The programme may not have been |
| |
|
| ejected, the power shuts off and |
| during timer recording. |
| recorded in its entirety. Next time |
| |
|
| “ä“ and “]“ won’t stop |
|
|
|
| make sure you have enough time on |
|
|
| blinking. |
|
|
|
| the tape to record the entire |
|
|
|
|
|
|
|
| programme. |
|
|
|
|
|
|
|
|
|
|
