JVC HR-S8009UM manual Function settings, Function Set screen, Select Function, Change setting

– Other Functions –

Function settings

You can use the other useful function settings on the Function Set screen.

A Access Main Menu screen, then	MAIN MENU
Function Set screen
	TUNER SET
	FUNCTION SET
Press MENU on the Remote. Press rtto	INITIAL SET
move the highlight bar (arrow) to
“FUNCTION SET”, then press OK or e.
	PRESS ( , ), THEN (OK)
B Select Function	PRESS (MENU) TO END

Press rtto move the highlight bar (arrow) to the function you want to set.

FUNCTION		PREVIOUS PAGE
S-VHS ET	OFF	VIDEO STABILIZER	OFF
B.E.S.T.	ON	BLUE BACK	ON
PICTURE CONTROL	AUTO	2ND AUDIO RECORD	OFF
AUTO TIMER	OFF	AUDIO MONITOR	HI-FI
SUPERIMPOSE	ON	S-VHS MODE	ON
AUTO SP EP TIMER	OFF
NEXT PAGE
SELECT WITH ( , ) AND (OK)		SELECT WITH ( , ) AND (OK)
PRESS (MENU) TO END		PRESS (MENU) TO END

CChange setting

Press OK or e. The default setting is bold in the following table. Press MENU to return to normal screen.

S-VHS ET — ON/OFF

When this function is set to “ON”, you can record on VHS cassettes with S-VHS picture quality. Tapes recorded using this function can be played back on most of S-VHS VCR or VHS VCR equipped with the SQPB (S-VHS QUASI PLAYBACK) function. When this function is set to “ON”, the S-VHS indicator lights up on the display panel.

●Before recording, set “B.E.S.T.” to “ON”. ( See below)

●You cannot activate the S-VHS ET function while recording, timer-recording or Instant Timer Recording ( pg. 9) or the “B.E.S.T.” function ( See below) is in progress.

●The S-VHS ET function does not work with S-VHS cassettes.

●To keep the highest quality recording and playback pictures over a long period of time, S-VHS recording on S-VHS cassettes is recommended.

●Use of high grade tapes is recommended for S-VHS ET recordings. On some tapes, picture quality will not improve even if the S-VHS ET function is used. Check the recording quality before you start important recordings.

B.E.S.T. — ON/OFF

When B.E.S.T. (Biconditional Equalized Signal Tracking) system is set to “ON”, this VCR checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible pictures. This takes place whenever you play back a tape or start recording after inserting a tape.

NOTE:

The VCR checks the tape condition for about 7 seconds, then starts recording. To make sure you record the desired scene or program completely, perform the following steps:

APress and hold PAUSE (9), and press REC (7). After about 7 seconds, the VCR re-enters Record Pause mode.

BPress PLAY (4) to start recording.

PICTURE CONTROL — AUTO(NORM)/EDIT/SOFT/SHARP

This function helps you to adjust the playback picture quality according to your preference.

AUTO (NORM): Normally select this. Picture quality is adjusted automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear instead of “AUTO”.

EDIT: Minimizes picture degradation during editing (recording and playback).

SOFT: Reduces image coarseness when viewing overplayed tapes containing much noise.

SHARP: Clearer, sharper-edged picture when viewing images with much flat, same-colored surfaces such as cartoons.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing the tapes, select “AUTO”.

AUTO TIMER — ON/OFF

●When this function is set to “ON”:

The timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press # to engage or disengage the timer recording standby mode.

●When this function is set to “OFF”:

You have to press # to engage or disengage the timer recording standby mode.

SUPERIMPOSE — ON/OFF

When this function is set to “ON”, various VCR status information (on-screen display) appears on the screen.

NOTE:

When you use this VCR as the playback VCR for editing a tape, be sure to set this function to “OFF”; otherwise, the VCR status information (on-screen display) will be recorded on the edited tape.

AUTO SP]EP TIMER — ON/OFF

When this function is set to “ON”, the VCR automatically switches to EP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example, Recording a program of 140 minutes in length onto a 120-minute tape

Approximately 110 minutes	Approximately 30 minutes
SP mode	EP mode

NOTES:

●If you have programed the VCR to timer-record 2 or more programs, do not use this function, but change the tape speed manually during timer programing.

●There may be some noise and sound disturbance where the tape speed switches from SP to EP mode on the tape.

●This function is not available during ITR (Instant Timer Recording), and will not work properly on the following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.

VIDEO STABILIZER — ON/OFF

When this function is set to “ON”, you can automatically correct vertical vibrations in the picture when playing back unstable recordings made on another VCR.

NOTE:

To watch recordings with close-caption or when you finish viewing a tape, set this function to “OFF”.

— 12 —