JVC HR-S8600EK setup guide TimeScan Audio, Speed SP Speed LP Audio output, Audio is output

MODE SET

B. E. S. T.ON

PICTURE CONTROL AUTO

AUTO TIMER OFF

O. S. D.ON

DIRECT RECON

AUTO SP=LP TIMER OFF

DIGITAL 3RON NEXT PAGE

27

TimeScan

Names of special-effects playback

Speed SP

Speed LP

Audio output

Reverse

Forward

Search

Play

Slow-Motion

*Still

Slow-Motion

Play

Search

(Time Jog**)

(Time Jog**)

-9x

-7x

-5x

-3x

-1x

-1/2x

-1/3x

0

1/3x

1/2x

1x

1.5x

2x

3x

5x

7x

9x

-7x

-3x

-1/2x

0

1/2x

1x

1.5x

2x

5x

9x

Audio is output.

Audio is not

Audio is

Audio is

Audio is output.

output.

output.

output.

** To activate the Still mode from the remote control press PAUSE button. Still mode cannot be engaged using the remote control's @ # button.

** Smooth slow motion delivering an uninterrupted moving image without distortion.

●If the picture jitters vertically, noise appears or the upper or lower part of the picture is distorded at -1/2x, -1/3x, 1/3x, 1/2x or 1.5x normal speed, use TV PROG + or – to correct the picture.

●Noise tends to appear at -9x or 9x normal speed during TimeScan search.

●When noise appears or the upper or lower part of the picture is distorted during TimeScan search, press and adjust tracking with TV PROG + or – button.

●The speed is shown during TimeScan in the upper right corner of the TV screen for approx. 5 seconds. (On some TVs the display may be distorted.)

●To resume normal playback, press PLAY.

●When using the recorder's TIME SCAN SHUTTLE ring, the playback speed may not change in the correct step if it is turned too fast.

●Picture and audio may occasionally become distorted when the recording speed changes. If this happens, resume normal playback once, and then try using TimeScan again.

●The picture may be noisy or there may be a loss of colour when you change the playback speed. (More noise will appear with LP recordings.)

●Noise may appear or the upper part of the picture may be distorted during still, frame-by-frame playback, 2x search of LP recordings, or with certain tapes.

●Picture may appear distorted in comparison to normal playback.

●When normal playback resumes from search (including TimeScan), still, slow motion or frame-by-frame playback, the picture may jitter vertically momentarily depending on the type of TV being used.

●Depending on the tape in use, noise may appear or the upper part of the picture may be distorted.

●In TimeScan mode there will be a time lag between the video and the audio and noise may appear in the audio signal.

●TimeScan sound quality will differ in comparison to normal playback.

●When material such as music videos where there is non-stop sound (very few breaks in the soundtrack) are viewed at 1.5x or 2x normal speed, the audio playback may be faster than normal.

●Depending on the type of tape contents, the sound may not be clear during forward slow-motion playback.

●Time Jog cannot be activated by pressing PAUSE for longer than 2 seconds.

●When the playback direction is reversed, it takes approximately 6 seconds until sound is heard.

●TimeScan does not work with NTSC playback.

If you don't want to hear TimeScan audio, set the "TIME SCAN AUDIO" to OFF. (See below)

TimeScan Audio

The audio output can be set ON/OFF during TimeScan. Select ON/OFF as required. * The default setting is "ON".

1Press MENU to access the Main Menu screen.

2Move the highlight bar (pointer) to "MODE SET" by pressing %Þ, then press OK or #.

3 Move the highlight bar (pointer) to "TIME SCAN AUDIO" by pressing %Þ, then press OK or #to select "ON" or "OFF".

4Press MENU to return to the normal screen.

PREVIOUS PAGE
POWER SAVE	OFF
S-VHS	AUTO
AV1 SELECT	VIDEO
AV2 SELECT	AV2
TIME SCAN AUDIO	ON

[5°] =	[5°] =
[MENU] : EXIT	[MENU] : EXIT