JVC KA-MR100G Troubleshooting

Others

Troubleshooting

Symptom	Cause(s)	Actions	Refer to
Power does not turn	Power is supplied from the DC INPUT	Attach the battery. The power of the memory recorder	A Page 7
on	terminal of the camcorder.	cannot be supplied from the DC INPUT terminal of the
		camcorder.
	Only the power of the camcorder is turned	It is necessary to turn on the power of the memory recorder	A Page 7
	AOnB.	at the same time.
	Remaining battery level is insufficient.	Charge the battery.	A Page 14
Unable to record or	The IEEE1394 cable is not connected.	Connect a GY-HD200/HD250 series camcorder to the	A Page 7
play clip		KA-UM100G adapter using an IEEE1394 cable.
	The [INT/EXT] switch setting of the	● Set to AEXTB during normal use. (When IEEE1394	A Page 7
	KA-UM100G adapter is inappropriate.	connection is made internally without the use of an
		external cable, set to AINTB.
		● If the ANO SIGNALB message does not disappear even
		if the setting is correct, set the switch again to select the
		setting. If the message remains displayed, turn off and
		on the power again.
	The video formats of the camcorder and	Ensure that the video format of the camcorder and memory	A Page 9
	memory recorder are not consistent with	recorder are consistent with each other.
	each other.
	The [IEEE1394] switch of the camcorder is	Set the [IEEE1394] switch to the AHDVB end.	A Page 9
	set to the ADVB end.	If the ANO SIGNALB message does not disappear even	A Page 10
		after setting to AHDVB, set the switch again. If the message
		remains displayed, turn off and on the power again.
Recording does not	The camcorder is set to the AVTRB mode.	Set to the ACAMB mode using the [CAM/VTR] button.	A Page 9
start
	The [1394 REC TRIGGER] item on the	Set [1394 REC TRIGGER] to ASYNCROB or ASPLITB.	A Page 9
	OTHERS[2/2] menu screen of the	When this is set to ASERIESB, recording starts when the
	camcorder is set to AOFFB or ASERIESB.	remaining capacity of the cassette tape falls below three
		minutes.
	The memory recorder is set to the playback	Press the [STOP] button to stop playback.	A Page 9
	mode.
	The write-protect of the SxS memory card	Set the write-protect switch to AOffB before recording or	A Page 14
	is enabled.	deleting a clip.
	There is no space left on the SxS memory	Use an SxS memory card that has sufficient space.	A Page 14
	card.
Unable to play clip	The camcorder is set to the ACAMB mode.	Set to the AVTRB mode using the [CAM/VTR] button.	A Page 10
	The cassette tape is currently being played	Stop playback of the cassette tape before playing back	A Page 10
	back.	data on the SxS memory card.
	A clip without the check mark (v) is	Set the camcorder and memory recorder according to the	A Page 10
	selected.	video format displayed when a clip is selected.
	The memory recorder is in the recording or	Press the [STOP] button to stop playback.	A Page 10
	standby mode.
	The clip may be damaged.	Execute ARESTOREB using this memory recorder.	A Page 14
No response when a	The [OPERATION] menu is set to ALOCKB.	Change the [OPERATION] menu setting to AUNLOCKB.	A Page 14
button is pressed
	A multiple number of buttons are pressed	Insert a short pause between each button operation.
	at the same time, or the same button is hit		^
	repeatedly.
Access lamp does not	The SxS memory card is not completely	Make sure that the SxS memory card is fully inserted into	A Page 8
turn on	inserted into the card slot.	the slot.
	The SxS memory card is inserted with the	Identify the face of the SxS memory card with the label,	A Page 8
	label facing the opposite direction.	and make sure that the card is correctly oriented before
		inserting.
SxS memory card	A SxS memory card that is formatted by	Execute AFORMATB using this memory recorder.	A Page 13
cannot be used	another device is used.
	A media that is not supported is inserted.	Replace it with a recommended SxS memory card.	A Page 14
	The clip is faulty.	Execute ARESTOREB or AFORMATB using this memory	A Page 14
		recorder. If doing so does not eliminate the error, replace it
		with a recommended SxS memory card.
Error message	ADR-HD100 POWER ?B appears when the	Connect and turn on the power of the memory recorder.	A Page 6
appears on the	memory recorder is not powered on or is		A Page 7
camcorder panel	not connected.
display	AHDD NO 1394 SIGNALB appears if the	Set the camcorder to the AVTRB mode.	A Page 10
	camcorder is set to the “CAM” mode when
	the memory recorder is in playback mode.
	AHDD SPACE LOWB appears when the	Use an SxS memory card that has sufficient space.
	space on the SxS memory card is		^
	insufficient or an SxS memory card is not
	inserted.

15