– Other Functions –

AUTO SP]LP TIMER — ON / OFF

When this function is set to “ON”, the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example, Recording a PAL-broadcast programme of 210 minutes in length onto a 180-minute tape.

Approximately 150 minutes

Approximately 60 minutes

SP mode

LP mode

 

 

Total 210 minutes

NOTES:

If you have programed the recorder to timer-record 2 or more programs, do not use this function, but change the tape speed manually during timer programing.

There may be some noise and sound disturbance where the tape speed switches from SP to LP mode on the tape.

The Auto SP]LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths.

Multi-Brand Remote Control

This remote control can control some functions of remote controllable TVs, cable boxes, satellite receivers or DVD sets listed below. Without setting, you can control a JVC TV.

NOTES:

Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.

Depending on the type of unit, some or all functions cannot be operated using this remote control.

It’s not possible to operate a unit not equipped with a remote sensor.

It’s not possible to set the remote control for two units at the same time.

Once you have set the remote control to operate the unit, you do not have to set it until you replace the batteries from the remote control.

TV Brand Setting

ATurn on TV

Turn on the TV using the Power button on the TV or its remote control.

BSet TV brand code

APress and hold TV.

BPress the Number keys to enter your TV’s brand code. C Press OK, and release TV. The TV should turn off.

COperate TV

First, press TV to set the remote control to TV mode, then press one of the following buttons: 1, TV/VCR, TV PR+/–, ^ (TV Muting), TV %+/–, and the Number keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

TV BRAND

CODE

TV BRAND

CODE

 

 

 

 

JVC

01, 23, 24, 25

MITSUBISHI

03

AIWA

36

MIVER

29

BEIJING

22

NEC

20

CCE

02

NOBLEX

22

CHANGHONG

34

NOKIA

31

DAEWOO

17, 37

PANASONIC

04, 11

FERGUSON

27

PEONY

34, 38, 39

FINLUX

30

PHILICO

10, 17, 21

FUNAI

32

PHILIPS

02, 42

GRADIENTE

15

SAMSUNG

12, 33, 34, 35

GRUNDIG

19

SANYO

13, 16

HITACHI

10

SHARP

06

ITT

28

SONY

07

JINXING

38

TCL

41

KONKA

40

THOMSON

26

LG/GOLDSTAR

18

TOSHIBA

08, 14

Cable Box, Satellite Receiver or DVD Brand Setting

ATurn on the unit

Turn on the cable box, satellite receiver or DVD using the Power button on the unit or its remote control.

BEnter brand code

APress and hold CABLE/SAT/DVD.

BPress the Number keys to enter your unit’s brand code. C Press OK, and release CABLE/SAT/DVD.

COperate the unit

First, press CABLE/SAT/DVD to set the remote control to cable box, satellite receiver or DVD mode, then press one of the following buttons:

For satellite receiver and cable box . . .

1, TV PR+/–,Number keys.

For DVD. . .

1, PLAY (4), STOP (8), PAUSE (9), FF (5), REW (3), w e (2 6) keys.

For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

To change the unit’s channels, press TV PR+/– or the Number keys. (The PR+/– button can be used to change the recorder’s channels only.)

Page 11
Image 11
JVC LPT0593-001B manual Multi-Brand Remote Control, TV Brand Setting, Other Functions