Page 8 October 23, 2001 10:00 am
Timer Recording
Up to 8timer recording programs can be made using G-CODE
timer programing or Express timer programing method as far as a
year in advance. Remember, the clock must be set before you can
program the timer.
NOTES:
●If all the 8programs have already been set, “PROGRAM FULL”
appears on the TV screen.
●After timer recording is completed, the recorder turns off
automatically.
●You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
●In case of a power failure after programming, the recorder’s
memory backup keeps your selections (if the lithium battery is
not exhausted).

G-CODE System Setup

INFORMATION
The G-CODE timer programming system eliminates the need to
input channel, date, start and stop time data when setting the
timer record function. Simply key in the G-CODE number for the
TV programme you wish to record (found in most TV listings) and
the recorder's timer is automatically programmed.
You have to set “GUIDE PROG” numbers, which are assigned to
each station for purposes of G-CODE timer programming, for all
the stations stored in your recorder’s memory to get proper results.
Before G-CODE setup you must have performed the procedures of
Tuner Set and Clock Set.
IMPORTANT
Perform the following procedure after Auto Set Up and/or the
channel setting steps.
After setting the Guide Program Numbers, channel positions may
be incorrect if you stored or skipped channels. In this case, re-
perform Guide Program Number setting.

Guide Program Number Set

AAccess Main Menu screen, then Initial Set screen
Press MENU on the remote control. Press rt to place the
pointer next to “INITIAL SET”, then press OK or e.
BAccess G-CODE Setup screen
Press rt to place the pointer next to “G-CODE SETUP”, then
press OK or e.
CInput Guide Prog number
Press rt or the Number keys to select
the Guide Program number as shown in
the TV listing, then press OK or e.
DInput receiving channel number
Press rt or the Number keys to select
the number of the channel on which the
Guide Program number’s broadcasts are
received, then press OK or e.
●If the satellite broadcast is received on
your recorder's auxiliary channel (“L-1”
or “F-1”), select “L-1” or “F-1” for the channel position to which
the satellite receiver is connected.
●Repeat steps 3 and 4 as necessary.
EReturn to normal screen
Press MENU on the remote control.

G-CODE Timer Programing

The G-CODE numbers are the numbers
next to the program in most TV listing.
●Remember, the clock must be set
before you can program the timer.
●Be sure to read “G-CODE®”.
●Load a cassette with the record safety
tab intact. The recorder turns on, and
the counter is reset, automatically.
●Select the appropriate colour system
with “PAL/MESECAM” and “NTSC”
in Function settings.
APress PROG on the remote control
to access the G-CODE screen.
BPress the appropriate Number keys
to input the G-CODE number, then press OK. Check to make
sure the setting is accurate on the G-CODE Program screen.
●If the G-CODE Setup screen appears
after pressing OK, press the Number
keys, PR+/– or rt to input the
number of the channel on which the
broadcast for the G-CODE number is
received on the recorder, then press
OK.
●To set the tape speed, press SP/LP/EP.
●To change the stop time, press STOP+/–.
●To timer-record daily (Monday–Friday) or weekly serials,
press DAILY or WEEKLY. Pressing the button again makes the
“DAILY” or “WEEKLY” display disappear.
At the programme check screen...
When the weekly serials are programmed, a day of the week
appears. When the daily serials are programmed, “DAILY”
appears.
●If you made a mistake, press & to access the G-CODE screen
again.
●If an incorrect G-CODE number or the one for a broadcast
already finished has been inputted, “ERROR” is displayed for
about 5seconds, then the G-CODE screen reappears.
CPress OK or PROG.
●If “PROGRAM OVERLAPPED” appears, see “Program
overlap warning display”.
DPress #. The recorder turns off automatically and “#” is
displayed on the display panel.
NOTE:
●If the tape reaches its end during timer recording, the recording
stops and “#”, “䡬” and “$” on the front display panel blink.
G-CODE SETUP
GUIDE PROG TV PROG
2 5
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-CODE SETUP
GUIDE PROG TV PROG
2 5
[0–9] OR [ / ] : SELECT
[MENU] : EXIT
G-CODE NO.
[0 – 9]
[+/–] : EXPRESS PROGRAMING
[PROG] : EXIT
[0 – 9]
[ ] : DELETE
[PROG] : EXIT
G-CODE NO.
1 2 3 4 5 6 7 8
: [OK]
– P1 –
NO. 12345678
START STOP
21:00 22:00
SP
DATE TV PROG
25.04 1
G-CODE SETUP
GUIDE PROG TV PROG
2 5
[0–9] OR [ / ] : SELECT
[PROG] : EXIT