These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

INTRODUCTION

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and auto channel scan, which automatically scans and memorizes viewable channels.

Before you begin:Make sure if the unit is connected to antenna or cables.

1After making all the necessary connections, press [POWER] to turn on the unit.

• This operation may take a few moments.

2Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI i i l Setup

Select the language for setup display.

English

Elija el idioma de ajuste.

 

Español

Sélectionner langue écran config.

Français

Select

ENTER Enter

SETUP

Skip

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].

3Use [Cursor K/L] to select “Air” for TV channels or “Cable” for CATV channels, then press [ENTER].

InitialI i i l Setup

Make sure the antenna is connected to "ANT.IN" jack.

Air

Select the destination of "ANT.IN" jack.

 

Cable

 

 

 

Air

 

 

 

Cable

Or

 

 

 

ANT.IN

 

 

 

 

Select

ENTER Enter

BACK

SETUP

Back

Skip

4Use [Cursor s/ B] to select the desired mode for energy saving, then press [ENTER].

InitialI i i l Setup

Select “Retail” or “Home” for your location.

Retail

Home

Select

ENTER Enter

•Select “Retail” if you want backlight to be brighter.

•Select “Home” to reduce the power consumption.

•When the initial setup is completed, the lowest memorized channel with the confirmation message of the energy saving mode will be displayed on the TV screen.

Note:

•If you connect the cable system directly, contact the CATV installer.

•If you press [POWER] or [SETUP] during auto channel scan, this setting will be canceled.

•The initial auto channel scan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set auto channel scan again. (Refer to page 18.)

•If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

2-2

No channel is registered.

Press and hold "ENTER" key on the remote control for 3 seconds.

Contact support hotline provided on manual or back of unit.

Sin canal registrado.

Pulse durante 3 segundos la tecla "ENTER" en el control remoto.

Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign.

Enfoncez "ENTER" 3 secondes sur la télécommande.

Contacter numero d'urgence dans manuel ou arrière appareil.

•When you select “Home”, brightness of backlight darkens compared to “Retail”. This is not a malfunction.

INFORMATION TROUBLESHOOTING SETTING OPTIONAL TV WATCHING PREPARATION

•Scanning and memorizing of channels start automatically.

InitialI i i l Setup

Now the system is scanning for channels,please wait.

5%

Analog channels

1ch

 

 

 

 

 

 

 

 

Digital channels

0ch

 

 

 

 

 

 

 

SETUP

Skip

After an initial setup is completed...

•If you want to scan the channels automatically again, refer to “Auto Channel Scan” on page 18.

•You can add the desired channels unmemorized by “Autoscan”. Refer to “Manual Register” on page 20.

•If you want to change the other language from the one you chose, refer to “Language Selection” on page 21.

•If you want to change the mode for energy saving, refer to “Energy Saving Mode” on page 32.

13

EN