JVC RX-D301S, RX-D302B Changing the display brightness, Turning off the power with the Sleep Timer, Making sounds natural, Press SLEEP repeatedly, Press DIMMER repeatedly

Changing the display brightness

You can dim the display—Dimmer.

From the remote control ONLY:

Press DIMMER repeatedly.

•Each time you press the button, the display brightness changes as follows:

DIMMER 1: Dims the display.

DIMMER 2: Dims the display more than DIMMER 1.

DIMMER 3: Turns off the display.

(Temporarily canceled when you operate the receiver.)

DIMMER OFF: Cancels the Dimmer (normal display).

Turning off the power with the Sleep Timer

You can fall asleep while listening to music—Sleep Timer.

From the remote control ONLY:

Press SLEEP repeatedly.

•Each time you press the button, the shut-off time changes in 10 minute intervals. The SLEEP indicator lights up on the display.

SLEEP indicator

ANALOG

AUTO SURR

SLEEP

S.WFR

10min20min30min40min 50min60min OFF (canceled) 90min 80min 70min

When the shut-off time comes:

The receiver turns off automatically.

To check or change the remaining time until the shut-off time:

Press SLEEP once.

The remaining time (in minutes) until the shut-off time appears.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer:

Press SLEEP repeatedly so that “SLEEP OFF” appears on the display. (The SLEEP indicator goes off.)

•The Sleep Timer is also canceled when you turn off the receiver.

Making sounds natural

JVC’s CC (Compression Compensative) Converter eliminates jitter and ripples, achieving a drastic reduction in digital distortion by processing the digital music data in 24 bit-quantization and by expanding the sampling frequency to 176.4 kHz (for fs 44.1 kHz signals)/192 kHz (for fs 48 kHz signals) on the front speakers. By using the CC Converter, you can obtain a natural sound field from both digital and analog sources.

Press CC CONVERTER repeatedly.

•Each time you press the button, the mode changes as follows:

CC CNVRTR 1: Select when playing back an analog source or a digital source with non compressed digital sound signal (Linear PCM).

The CC CONVERTER 1 indicator lights

up on the display.

CCCNVRTR 2: Select when playing back a source with compressed digital sound signal (Dolby Digital or DTS).

The CC CONVERTER 2 indicator lights

up on the display.

CC CNVRTR OFF: Select when not using the CC Converter.

NOTE

When “DVD MULTI” is selected as the source, this function is not available.

Basic adjustment of auto memory

This receiver memorizes sound settings for each source:

•when you turn off the power, and

•when you change the source.

When you change the source, the memorized settings for the newly selected source are automatically recalled.

The following can be stored for each source:

•Analog/digital input mode (see page 14)

•Bass boost (see page 25)

•Digital equalization pattern (see page 24)

•Input attenuator mode (see page 25)

•Midnight mode (see page 21)

•Speaker output level (see page 24)

•Surround/DSP mode selection (see page 33)

NOTE

If the source is FM or AM, you can assign a different setting for each band.

Signal and speaker indicators on the display

Signal indicators							Speaker indicators
L	C	R						L	C	R
S.WFR		LFE	ANALOG	DUAL MONO		AUTO SURR		S.WFR		LFE
LS	S	RS	DIGITAL AUTO	L	C R	HEADPHONE		LS	S	RS
			LINEAR PCM	S.WFR LFE		PL	x
SB	SB	SB	DIGITAL	LS	S RS	NEO : 6	DSP	SB	SB	SB
			96 / 24			3D-PHONIC
				SB	SB SB
						VIRTUAL SB

The signal indicators light up as follows:

L:• When digital input is selected: Lights up when the

left channel signal comes in.

•When analog input is selected: Always lights up.

R:• When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C:Lights up when the center channel signal comes in. LS: Lights up when the left surround channel signal comes

in.

RS: Lights up when the right surround channel signal comes

in.

S:Lights up when monaural surround signal comes in. SB: Lights up when the surround back channel signal

comes in.

LFE: Lights up when the LFE channel signal comes in.

NOTE

When “DVD MULTI” is selected as the source, all the signal indicators except “SB,” “S,” and “LFE” light up.

The speaker indicators light up as follows:

•The subwoofer indicator ( S.WFR ) lights up when “SUBWOOFER” is set to “SUBWFR <YES>.” For details, see page 19.

•The other speaker indicators light up only when the corresponding speaker is set to “SML (small)” or “LRG (large),” and also when required for the current playback.