JVC RX-DP15B SUBWFR LFE, Adjusting the Zone 1 Volume, Selecting different sources for picture and sound

The signal indicators light up to show the incoming signals.

L: • When digital input is selected: Lights up when the left channel signal comes in.

•When analog input is selected: Always lights up.

R: • When digital input is selected: Lights up when the right channel signal comes in.

•When analog input is selected: Always lights up.

C: Lights up when the center channel signal comes in. LFE : Lights up when the LFE channel signal comes in.

LS : Lights up when the left surround channel signal comes in.

RS : Lights up when the right surround channel signal comes in.

S : Lights up when the monaural surround channel signal comes in.

SB : Lights up when the surround back channel signal comes in.

Selecting different sources for picture and sound

While watching pictures from a video source (DVD player, VCR, or DBS tuner), you can listen to sound of an audio source.

•Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.

Press one of the audio source selecting buttons— PHONO, CD, TAPE/MD, CDR, FM/AM,

EXT 7.1CH—while viewing the picture from a video component such as the VCR or DVD player, etc.

DVD DVD MULTI VCR 1 VCR 2 TV/DBS VIDEO CD PHONO TAPE/MD CDR FM/AM EXT 7.1CH

Notes:

•When “DVD MULTI” is selected as the source, “L,” “C,” “R,” “LFE,”

“LS” and “RS” light up.		On the unit
• When “EXT 7.1CH” is selected as the source, “L,” “C,” “R,” “LFE,”
“LS,” “RS,” and “SB (left/right)” light up.	DVD	DVD MULTI	PHONO	CD
However, “SB” will not light if the THX mode or the DSP mode is
activated or if “SPEAKER 2” is set to “BI-AMP OUT” (see page 44).	VCR 1	VCR 2	TAPE/MD	CDR
	TV/DBS	VIDEO	FM/AM	EXT 7.1CH
How to use the speaker and signal indicators
To obtain the best performance of this receiver while using
the Surround/THX/DSP modes, check the speaker and signal		From the remote control

indicators on the display carefully and set the speakers correctly.

						Adjusting the Zone 1 Volume
L	C R	Ex. No sound comes out of the
					On the unit:
		center speaker and surround
SUBWFR LFE					To increase the volume, turn MASTER
		back speakers though center						MASTER	VOLUME
LS	RS	channel and surround back			VOLUME clockwise.
		channel signals are coming			To decrease the volume, turn it
	SB	into this receiver.			counterclockwise.
					• When you turn MASTER VOLUME		Down			Up
						rapidly, the volume level also changes
About Dual Mono						rapidly.
					•	When you turn MASTER VOLUME slowly,
Dual Mono can be easily understood when you think of the						the volume level also changes slowly.
bilingual broadcast or the MTS (Multi-channel TV Sound) used					From the remote control:
for some TV programs (however, the Dual Mono format is not
identical with those analog formats).					To increase the volume, press VOLUME +.			VOLUME
This format is now adopted in Dolby Digital, DTS, and so on. It					To decrease the volume, press VOLUME –.
allows two independent channels (called main channel and sub-
channel) to be recorded separately.					CAUTIONS:
• When Dual Mono signals are detected, the
DUAL indicator lights up.					•	Always set the volume to the minimum before starting any source. If
You can select either channel you want to						the volume is set at a high level, the sudden blast of sound energy
listen to (see page 42).		DUAL indicator			•	can permanently damage your hearing and/or ruin your speakers.
						Be careful not to turn up the volume too high when controlling the
			DUAL	DGTL AUTO		receiver without listening to the playback sound. For example, when
			L	R		adjusting the volume level in Zone 2 from Zone 1.
			SUBWFR	DIGITAL
					Notes:
					• The volume level can be adjusted within the range of “– – – dB”
						(minimum), “–71.0 dB” to “+18.0 dB” (maximum).
					• If you set One Touch Operation to “ON” (see page 44), you do not
						have to adjust the volume level each time you change the source. It
						is automatically set to the stored level. (However, if you have turned
						off the receiver with the volume level set at more than level “–35
						dB,” the volume level will be automatically set at level “–35 dB” next
						time you turn on the receiver.)

24