JVC RX-DP15B DVD, CDR, VCR, PHONO, TV/DBS, control, CONTROL, CD DISC, TAPE/MD, DVD MULTI, If you have pressed, If you have pressed, If you have pressed

TV

CATV/

DBS

4.Press one of the learning buttons, to which you want to assign a signal from the target remote

control.The LEARN indicator starts flashing.

•If you have pressed DVD or DVD MULTI in step 3, you can store the signals into the following buttons:

			/ REW	PLAY	FF/
		EFFECT	DOWN	TUNING	UP
1	2	3		STOP	PAUSE
		LIVENESS
4	5	6
7/P	8	9
				SET
10	0	+10
RETURN	FM MODE	100+

•If you have pressed PHONO in step 3, you can store the signals into the following buttons:

PLAY

TUNING

STOP

•If you have pressed TV/DBS in step 3, you can store the signals into the following buttons:

–By setting the TV operation mode selector

either to “TV” or “CATV/DBS,” you can store a different set of signals into the following buttons.

TV/CATV/DBS

STANDBY/ON

		EFFECT
1	2	3	TV/VIDEO
		LIVENESS
			TV VOL CHANNEL
4	5	6
7/P	8	9
10	0	+10
RETURN	FM MODE	100+

5. While the LEARN indicator is flashing, press the button on the target remote control.

The signal from the target remote control is sent to this remote control.

LEARN

•If you have pressed CD, or CONTROL to select “CD DISC,” in step 3, you can store the signals into the following buttons:

–You can store a different set of signals into the following buttons separately for “CD” and “CD DISC.”

		EFFECT
1	2	3	/ REW	PLAY	FF/
		LIVENESS	DOWN	TUNING	UP
4	5	6
				STOP	PAUSE
7/P	8	9
10	0	+10
RETURN	FM MODE	100+

•If you have pressed TAPE/MD or CDR in step 3, you can store the signals into the following buttons:

		EFFECT
1	2	3	/ REW	PLAY	FF/
		LIVENESS	DOWN	TUNING	UP
4	5	6	REC	STOP	PAUSE
7/P	8	9
10	0	+10
RETURN	FM MODE	100+

•If you have pressed VCR 1 in step 3, you can store the signals into the following buttons:

VCR 1

STANDBY/ON

		EFFECT	PLAY
1	2	/ REW		FF/
		3
		DOWN	TUNING	UP
		LIVENESS
4	5	REC	STOP	PAUSE
		6
7/P	8	9
10		CHANNEL
	0	+10
RETURN	FM MODE	100+

“LEARN OK” appears and the LEARN indicator stops flashing and remains lit. The target signal is now stored in the button selected in step 4.

Notes:

•If the LEARN indicator stops flashing before you press the button on the target remote control, repeat from step 4 again.

•If “ERROR” appears on the display, you have failed in storing the signal. Try again. However some signals do not match with this remote control even though this remote control can learn most infrared signals.

6.• Repeat steps 4 and 5 to store more signals in the same remote mode (source).

•Repeat steps 3 to 5 to store more signals in adifferent remote mode (source).

7.Set the LEARN/TRANSMIT (ZONE 1/ZONE 2) selector to “TRANSMIT (ZONE 1/ZONE 2)” to finish the storing procedure.

LEARN	TRANSMIT		LEARN	TRANSMIT
ZONE 1		ZONE 2	ZONE 1		ZONE 2
For the Zone 1 operations			For the Zone 2 operations

Notes:

•The signals stored into this remote control from the target remote control deviate slightly from the original signals. Since some components will not accept these deviating signals, you may not be able to operate those components using this remote control even though the storing procedure has been successfully finished.

•When replacing the batteries, finish changing them without delay; otherwise, the stored signals are all erased.

79