JVC SR-L911UB [ ]: Factory setting

20

Alarm/sensor ALARM REC [OFF]

recording mode ON

setting

Turns the alarm recording function on or off.

Alarm recording is enabled only in the Timelapse Record mode.

An index code (VISS signal) is also recorded at the start point of alarm

recording as an alarm cue signal.

OFF :Alarm recording is disabled.

ON :This unit enters the 8H (EP) Record mode, when an alarm signal is input

to the rear panel's [ALARM IN] terminal during timelapse recording.

5-2 Contents of the Function Menu Switches

5 SETTING OF THE FUNCTION MENU SWITCHES

FunctionScreens Items Set values

[ ]: Factory setting

SENSOR REC [OFF]

ON

Selects the recording duration for alarm recording or sensor recording.

5 ..... 180 : Alarm or sensor recording is performed for the time specified (5 sec.

to 180 sec.).

TAPE END: Alarm or sensor recording continues until the tape ends.

MANUAL : Alarm or sensor recording continues for as long as alarm signals

are input.

Set to this position when specifying the alarm recording time with a

switcher.

DURATION 5

15

30

60

120

[180]

TAPE END

MANUAL

Turns the sensor recording function on or off. Sensor recording is enabled in

the Stop mode. An index code (VISS signal) is also recorded at the start point of

sensor recording.

OFF :Sensor recording is disabled.

ON :When an alarm signal is input to the rear panel's [ALARM IN] terminal in

the Stop mode. this unit automatically starts recording in the 8H (EP)

Record mode.

Selects whether or not the alarm buzzer sounds during alarm or sensor

recording.

OFF :The buzzer does not sound.

ON :The buzzer sounds.

TAPE END [STOP]

MODE REW

REPEAT

EJECT

BUZZER [OFF]

ON

Set the operation mode at tape end during recording in the case when alarm or

sensor recording is executed even once.

STOP :Stops at tape end.

REW :Rewinds the tape automatically and stops.

REPEAT : Rewinds the tape automatically to the beginning and restarts

recording.

EJECT :The tape is ejected.

Select the RS-232C data transfer speed from 1200 bps, 2400 bps, 4800 bps or

9600 bps.

RS-232C

parameter

setting BAUD RATE 1200

2400

4800

[9600]

This screen is displayed on the on-screen setting screen only when the (optional) RS-232C board

SA-K97U is installed.

Contents

Main INSTRUCTIONS SR-L911UB VIDEO CASSETTE RECORDER SAFETY PRECAUTIONS CAUTION ATTENTION INFORMATION CAUTION NOTE: CONTENTS 1 INTRODUCTION 2 CONTROLS AND CONNECTORS 3 CONNECTIONS 4 MONITOR ON-SCREEN DISPLAY 1 INTRODUCTION 1-2 Periodical Maintenance 1-3 Precautions 5 Handling and storage place 5 5 5 2 CONTROLS AND CONNECTORS 2-1 Front Panel 6816 4 3 2-1 Front Panel 7 8 9 0 2-2 Display 1 6 8 911 12 13 2 3 45 7 10 14 6 2-1 FRONT PANEL 2-3 Rear Panel 1 2 3 4 ! @ # $ % 3 CONNECTIONS 1 2 3 4 5 3-2 Connecting a System Using a Sequential Switcher 3 CONNECTIONS 1 2 the SR-L911UB. 3 4 5 3-3 Connecting the Rear Panel Input/Output Terminal Connections COM CAM SW OUT External interface example 5 4 MONITOR ON-SCREEN DISPLAY 4-1 On-Screen Display in the Time/Date and Record Modes 5 1 2 4-2 Main Menu Display 4 MONITOR ON-SCREEN DISPLAY 5 1 2 4-3 Alarm Input/Power Loss Data Display 1 2 3 4 5 5 SETTING OF THE FUNCTION MENU SWITCHES 5-1 Function Menu Switch Setting 5 1 2 3 [ Three function menu switch setting screens are available. [ ]: Factory setting [ ]: Factory setting [ ]: Factory setting 6 PREPARATION 6-2 Date and Time Setting 6-1 Cassette Loading/Unloading Loading Auto power on 6 PREPARATION Set the date and time using the CLOCK ADJUST menu screen. Set the date and time on the front panel display 1 2 3 4 6-4 Selection of Record/Play Mode 6-3 Summer Time Compensation Standard time 1 2 1 7 RECORDING 7-1 Preparation 5 7-2 Recording Recording Check 5 [ 1 [ 2 1 2 [ 3 [ n [ n 4. 5 16.30.00 6. 7 8 4 5 7-3 Timer Recording 2, 3 16.30.00 6 4, 5 Canceling timer programming 1 2 1 2 3 Notes on timer recording Changing a preset timer program 1 2 3 [ 4 AL 7-4 Alarm Recording 5 7-4 Alarm Recording Connect an alarm sensor to the rear panels alarm input terminal. 1 2 3 7-5 Sensor Recording Connect an alarm sensor to the rear panels alarm input terminal. 1 2 3 7-6 Repeat Recording Page 8-3 Special-Effects Playback Reverse playback 1 2 Still and field/frame advance 8-4 Index Search 5 When the picture moves up and down in the Still mode When noise appears in the picture in the Play/ Field Advance Play/Search mode n 9 TROUBLESHOOTING 9-1 Error Indication 5 5 5 8-3 Special-Effects Playback Reverse playback 1 2 Still and field/frame advance 8-4 Index Search 5 When the picture moves up and down in the Still mode When noise appears in the picture in the Play/ Field Advance Play/Search mode n 9 TROUBLESHOOTING 9-1 Error Indication 5 5 5 9-2 No Error Indication 9 TROUBLESHOOTING 10. OPTIONAL SA-K97U RS-232C INTERFACE BOARD 10-1. Installation of the SA-K97U 3. yourself on sharp edges and metal parts inside the VCR. Note: 10-2. SA-K97U Specifications 9-pin connector specifications Data format 5 5 5 5 5 10-3. SA-K97U RS-232C Protocol & Commands RS-232C protocol JVC table-1 JVC base table 10-3. SA-K97U RS-232C Protocol & Commands This section provides technical data for programmers. 30H 0AH Command description TXD B0H 33H 40H RXD 0AH 0AH 0AH 01H (or 05H) Search start Time 2-2 VCR setting commands TXD 7EH 30H 33H RXD 0AH 0AH 0AH Time 40H 0AH TXD 8EH RXD 0AH Time 30H 0AH 39H 0AH 33H 0AH 30H 0AH 39H 0AH 38H 0AH TXD 8FH RXD 0AH Time 31H 0AH 35H 0AH 32H 0AH 39H 0AH 35H 0AH 39H 0AH 2-3 Commands for VCR status verification * 2-4 Others (Input data correction/Error cancellation) TXD 7EH 30H 32H RXD 0AH 0AH 0AH Time 41H 0AH 33H 0AH 40H 0AH 3 Commands reference chart 11-1 Rear Panels Input/Output 11 APPENDIXES 11 APPENDIXES 11-2 Specifications [Time/date] [Alarm] [Accessories] [Video System]