CONNECTION/INSTALLATION
RM-P2580 System
System with up to 8 cameras
Connecting the control signal cable
(Use a twisted-pair cable for connection. Page 17.)
Camera 1
MACHINE ID:1 (Menu screen) RX TERM: OFF (switch)
Camera
Camera
Control signal cable | ||
Video signal cable | ||
Power | AC24V | |
or | ||
cable | ||
DC12V | ||
| ||
Camera 1 |
|
control signal | |
connection terminals | |
TX+ A | |
TX | B |
RX+ C | |
A RX | + |
B RX | + |
C TX | |
Connect: Camera TX+ to
Camera 2
MACHINE ID:2 (Menu screen) RX TERM: OFF (switch)
Camera 8
MACHINE ID:8 (Menu screen) RX TERM: ON (switch)
AC24V or DC12V
Camera |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
AC24V | • | • | • | • | • | CAM SW | Time lapse VCR |
or |
|
|
|
|
| OUT | |
DC12V |
|
|
|
|
|
|
|
|
|
|
|
|
|
| VIDEO IN |
MONITOR
RX | D |
Camera 2 |
|
control signal | |
connection terminals | |
TX+ A | |
TX | B |
RX+ C | |
RX | D |
D TX |
Camera RX– to
Setting the switches | ( Page 10) |
TO
CAMERA
TO CAMERA
- -
Remote Control Unit
RM-P2580
ON
|
|
| CAMERA | COM |
|
| |||
|
|
|
| SW |
|
| |||
|
|
| DATA I / O |
|
|
|
| ||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
| MONITOR |
|
|
|
| VIDEO INPUT |
|
|
|
|
|
|
|
|
|
|
|
| MONITOR MONITOR | OUTPUT 2 | |
|
|
|
|
|
|
| 1 | 2 | |
|
|
|
|
|
|
| OUTPUT OUTPUT |
| |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
|
|
|
| VIDEO OUTPUT |
|
|
|
|
|
|
|
|
|
|
|
|
| MONITOR | |
|
|
|
|
|
|
|
| OUTPUT 1 | |
MONITOR
SET |
|
|
CAMERA |
|
|
SETUP | EXT | ON |
MENU | INT/GL | LL |
DUPLEXSIMPLEX
RX | ON |
EXT
INT/GL
DUPLEX
RX
ON
LL
SIMPLEX
ON
Select the synchronization method of the camera image. Set the switch on all cameras to LL (Line Lock) and match with the V. PHASE. ( Page 26.)
Set this switch to the DUPLEX
* If the setting is changed, be absolutely sure to |
switch on the power again. |
NOT USED 
NOT USED
This is the connected example of the
VIDEO
DC
IRIS
Set this switch to ON (signal termination ON) only on the camera placed at the end of the control signal cable. Set to OFF on all other cameras.
•When operating a system using the
•Confirm switch settings on the screen as follows.MONITOR screen
qConfirm that the image from the camera to be checked | (example showing camera ID as “05”) |
| |
is displayed on the monitor. |
|
w Turn OFF and then ON the AC 24 V power to the |
|
|
|
| |
camera to be checked. |
|
|
|
| |
e The camera begins the initial operation and charac- |
|
|
|
| |
ters similar to those shown in the illustration on the |
|
|
|
| |
right appear on the monitor screen. |
|
|
|
| |
r Confirm that “DUPLEX” and |
|
|
|
| |
and that the ID number is the correct number (the | P R O T O C O L : D U P L E X | I D - 0 5 | |||
|
|
|
| ||
number should be the same as the number of the |
|
|
|
| |
VIDEO INPUT terminal to which the camera is con- |
|
|
|
| |
nected on the rear panel of the | “DUPLEX” | should | The number shown in the | ||
t If wrong, set the camera ID again. | |||||
be displayed. | □□ part of | ||||
| should be correct. | ||||
|
| ||||
|
|
|
| ||
Setting on the MENU screen ( Page 33)
* If the setting is changed, escape from the menu screen once, and definitely switch on the power again. | |||
C OMMUN I C A T I O N |
| Set to M.DROP | |
| Set to M.DROP when the | ||
|
| ||
S T Y L E | M . DROP | as a remote control unit. When controlling | |
MACH I NE I D | 1 | ||
from another machine, make sure that it | |||
|
| ||
|
| matches the communication system used. | |
MACHINE ID setting switches
Set this item to match the
INPUT terminal number for each camera.
When connecting
●Turn OFF the power supply to all equipment to be used before making connections.
●Carefully read the Instructions for each piece of equipment to be used before making connections.
●For the appropriate connection cables and the length of these, carefully read “Connections on the back” on page 16.
●The control signal cable cannot be used for loop connection.
