JVC TM-H1950CG manual HOW to USE the Menu, Set-up menu items Purpose Settings

HOW TO USE THE MENU

FUNCTIONS (cont’d)

Set-up menu items

Purpose

Settings

PICTURE SUB ADJ.

Image sub adjustment

Selects CONTRAST/BRIGHT/CHROMA/PHASE. The

selected setting screen is shown. Select the function display for

adjustment.

CONTRAST

Adjusts contrast.

– 10

– 9

• •

– 01

00

+01

• •

+09

+10

BRIGHT

Adjusts brightness.

– 10

– 9

• •

– 01

00

+01

• •

+09

+10

CHROMA

Adjusts color density.

*1

– 10

– 9

• •

– 01

00

+01

• •

+09

+10

PHASE

Adjusts hue.

*1

– 10

– 9

• •

– 01

00

+01

• •

+09

+10

H. POSITION

Adjusts the horizontal position of the

screen (+: Horizontal position shifts

– 5

• • •

– 01

00

+1

• • •

+5

to the right/-: Horizontal position shifts to

the left)

V. POSITION

Adjusts the vertical position of the screen

– 5

• • •

– 01

00

+1

• • •

+5

(+: Vertical position moves up/-: Vertical

position moves down)

WHITE BALANCE

Adjusts the white balance.

Selects the drive (DRV) or cut off (CUTO) adjustment. The selected

setting screen is shown. Select the function display for adjustment.

DRIVE

R. DRIVE

Adjusts red level.

– 20

– 1 9

• •

– 01

00

+01

• •

+19

+20

B. DRIVE

Adjusts blue level.

– 20

– 1 9

• •

– 01

00

+01

• •

+19

+20

– 20

– 1 9

• •

– 01

00

+

01

• •

+19

+20

CUT OFF

R. CUT OFF

Adjusts red cut off.

G. CUT OFF

Adjusts green cut off.

– 20

– 1 9

• •

– 01

00

+

01

• •

+19

+20

B. CUT OFF

Adjusts blue cut off.

– 20

– 1 9

• •

– 01

00

+01

• •

+19

+20

CONTROL LOCK

Sets the operation buttons on the front

O F F

ON

panel to control lock mode.

STATUS DISPLAY

Sets the status display of the color system.

OFF

ON

REMOTE SYSTEM

Sets the external control function method.

MAKE

TRG .

*2

INPUT REMOTE

Sets external control of input selection.

A – D

A/B

(Shown only when REMOTE SYSTEM is

*2

set to MAKE.)

*1 May not be shown depending on the type of signals input.

*2 Refer to HOW TO USE EXTERNAL CONTROL on page 18 for more details.

4.To set the other set-up menu items, repeat the procedures 2 and 3.

5.Press the MENU button to quit.

MENU		Front panel	Function	Contents
		button	displayed
		MENU	EXIT	Quit (or Release) the <MENU>
				screen
Note:
Setting	Description
MAKE	Make contact system: Controls the function using the control
	terminal’s short-circuit and open (short-circuits or opens 15th
	terminal (GND)).
TRG.	Trigger system: Controls the function by short-circuiting (short-
	circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-D	Switches the input by short-circuiting a specified signal line in
	INPUT A, B, C, or D.
A/B	Switches between INPUT A and INPUT B with D-sub pin 2.

Notes:

●When the CONTROL LOCK function is set to ON, pressing operation buttons on the front panel will display the message “CONTROL LOCK ON!” on the screen for about 3 seconds.

●The CONTROL LOCK function is maintained even when the power is turned off.

●To turn off the CONTROL LOCK function, while holding the MENU button press the CHROMA/PHASE button. Then set the CONTROL LOCK function to OFF.

●Even when the CONTROL LOCK function is set to ON, the following operations are available:

–Power Switch operation

–Volume control with the VOLUME/ SELECT buttons

–Display or disappear of the <SET-UP MENU> screen.

●The STATUS DISPLAY function can be set to display (ON) or not display (OFF) the present color system when the power is turned on or the input signal is changed. Refer to page 9 for more information.

●When REMOTE SYSTEM is set to MAKE and any one of the INPUT A to D buttons, the UNDER SCAN button, COLOR OFF button or the ASPECT button is pressed, “REMOTE ON!” appears on screen for about 3 seconds. (Not shown with CONTROL LOCK set to ON.)

●When REMOTE SYSTEM is set to TRG, the front panel controls can be operated.

●INPUT REMOTE and REMOTE SYSTEM are enabled when REMOTE ENABLE is set to ON.

14