JVC UX-P30 ]]

7

English

RIGHT LEFT

MAIN

SPEAKERS

SPEAKER

IMPEDANCE

MIN

4

1Connect the AM loop antenna to the AM

LOOP terminals as illustrated.

2Turn the AM loop antenna until you have

the best reception.

To connect an outdoor AM antenna

When reception is poor, connect a single vinyl-covered wireto the AM EXT terminal and extend it horizontally. The AMloop antenna must remain connected.

For better reception of both FM and AM

•Make sure the antenna conductors do not touch any other

terminals and connecting cords.

•Keep the antennas away from metallic parts of the unit,

connecting cords, and the AC power cord.

AM antenna

Vinyl-covered wire

(not supplied)

AM loop antenna

(supplied)

Connecting Speakers

Right speaker Left speaker

Black

Red

1Press and hold the clamp of the speaker

terminal on the rear of the unit.

2Insert the end of the speaker cord into the

terminal.

Match the polarity of the speaker terminals: Red ª tored ª and black · to black ·.•If the cords are covered with insulation,remove a short section of insulation atthe end of each cord by twisting andpulling it off.

3Release the finger from the clamp.

•DO NOT connect speakers while the power is

on.

•DO NOT connect more than one speaker to each

speaker teminal.

IMPORTANT: Use only speakers with the same speaker

impedance as indicated by the speaker terminals on the

rear of the unit.

Speaker

cord

Speaker

cord

1

2

AM EXT

FM

COAXIAL

AM LOOP

75

ANTENNA

]]

1

2

3

EN01-08_UX-P30[UW]f.pm6 03.6.4, 6:49 PM7

Contents

Main UX-P30 GVT0115-013A COVER_UX-P30[UW]f.pm6 03.7.2, 3:39 PM3 [UW] MICRO COMPONENT SYSTEM Page G-2 CAUTION PRECAUCIN PRECAUO G-3 15 cm 15 cm 15 cm 1 cm15 cm 1 cm 15 cm 10 cm G-4 IMPORTANT FOR LASER PRODUCTS IMPORTANTE PARA PRODUCTOS LSER IMPORTANTE PARA PRODUTOS LASER Introduction About This Manual Precautions Installation Power sources Contents Location of the Buttons and Controls Front Panel Display Window PRGM CLOCK RANDOM [DAILY REC SLEEP]REC ALL BASS SOUND MONOST Display Window Page 6 Getting Started Supplied Accessories Putting the Batteries into the Remote Control 3 1 ]] 3 8 Connecting Other Equipment 230V 127V 110V Common Operations Turning On the Power Setting the Clock Press CLOCK for more than 2 seconds. Press or 4 to adjust the hour, then press CLOCK. Reinforcing the Bass Sound Selecting the Sound Modes Selecting the Sources and Starting Play Adjusting the Volume + Listening to FM and AM Broadcasts Tuning in a Station and Repeat steps Press FM/AM. Tuning in a Preset Station Playing Back Discs (CD/CD-R/CD-RW) General Notes When playing a CD-R or CD-RW Playing Back the Entire DiscNormal Play Press CD 0 (or 0 on the unit). Basic Disc Operations To stop play for a moment Repeat step To go to another track To locate a particular point in a track Prohibiting Disc EjectionTray Lock ALL Playing at RandomRandom Play Repeating TracksRepeat Play ALL Playing Back Tapes Playing Back a Tape Press ) on the unit. Put a cassette in with the exposed part of the tape down. Close the cassette holder gently. Recording Recording on a Tape Put a recordable cassette in with the exposed part of the tape down. Close the cassette holder gently. Check the recording direction for the tape. Disc Direct Recording One Track Recording Using the Timers Using Daily Timer and Recording Timer Press and hold TIMER for more than 3 seconds. Set the on-time you want the unit to turn on at. Set the off-time you want the unit to turn off (on standby) at. Using Sleep Timer How Sleep Timer actually works Press SLEEP. Wait for about 5 seconds after specifying the time length. Maintenance Handling cassette tapes Handling discs Cleaning the unit Troubleshooting Symptom Cause Action Specifications