Manuals / Brands / Home Audio / Stereo System / JVC / Home Audio / Stereo System

JVC UX-P30 8, Now, you can plug the AC power cord.

1 28

Download 28 pages, 849.32 Kb

8

English

Connecting Other Equipment

You can connect audio equipment—used only as a playback

device.

•DO NOT connect any equipment while the power

is on.

•DO NOT plug in any equipment until all

connections are complete.

To connect audio equipment

Be sure that the plugs of the audio cords are colored: White

plugs and jacks are for left audio signals, and red ones for

right audio signals.

RL

AUX

To audio output

Audio equipment

For playing the other equipment through this unit, connect

between the audio output jacks on the other equipment and

AUX jacks by using audio cords (not supplied).

Adjusting the Voltage Selector

Before plugging in the unit, set the correct voltage for your

area with the voltage selector on the rear of the unit.

VOLTAGE

SELECTOR

110V

127V

230V

220V

Voltage mark

Use a screwdriver to rotate the voltage selector so the voltage

number the voltage mark is pointing at is the same as the

voltage where you are plugging in the unit. (See the back

cover page.)

DO NOT plug in before setting the voltage

selector on the rear of the unit and all connection

procedures are complete.

Now, you can plug the AC power cord.

•If the wall outlet does not match the AC plug, use the

supplied AC plug adaptor.

IMPORTANT: Be sure to check all connections to be done

before plugging the AC power cord into a wall outlet.

EN01-08_UX-P30[UW]f.pm6 03.6.4, 6:49 PM8

Contents

Main UX-P30 GVT0115-013A COVER_UX-P30[UW]f.pm6 03.7.2, 3:39 PM3 [UW] MICRO COMPONENT SYSTEM Page G-2 CAUTION PRECAUCIN PRECAUO G-3 15 cm 15 cm 15 cm 1 cm15 cm 1 cm 15 cm 10 cm G-4 IMPORTANT FOR LASER PRODUCTS IMPORTANTE PARA PRODUCTOS LSER IMPORTANTE PARA PRODUTOS LASER Introduction About This Manual Precautions Installation Power sources Contents Location of the Buttons and Controls Front Panel Display Window PRGM CLOCK RANDOM [DAILY REC SLEEP]REC ALL BASS SOUND MONOST Display Window Page 6 Getting Started Supplied Accessories Putting the Batteries into the Remote Control 3 1 ]] 3 8 Connecting Other Equipment 230V 127V 110V Common Operations Turning On the Power Setting the Clock Press CLOCK for more than 2 seconds. Press or 4 to adjust the hour, then press CLOCK. Reinforcing the Bass Sound Selecting the Sound Modes Selecting the Sources and Starting Play Adjusting the Volume + Listening to FM and AM Broadcasts Tuning in a Station and Repeat steps Press FM/AM. Tuning in a Preset Station Playing Back Discs (CD/CD-R/CD-RW) General Notes When playing a CD-R or CD-RW Playing Back the Entire DiscNormal Play Press CD 0 (or 0 on the unit). Basic Disc Operations To stop play for a moment Repeat step To go to another track To locate a particular point in a track Prohibiting Disc EjectionTray Lock ALL Playing at RandomRandom Play Repeating TracksRepeat Play ALL Playing Back Tapes Playing Back a Tape Press ) on the unit. Put a cassette in with the exposed part of the tape down. Close the cassette holder gently. Recording Recording on a Tape Put a recordable cassette in with the exposed part of the tape down. Close the cassette holder gently. Check the recording direction for the tape. Disc Direct Recording One Track Recording Using the Timers Using Daily Timer and Recording Timer Press and hold TIMER for more than 3 seconds. Set the on-time you want the unit to turn on at. Set the off-time you want the unit to turn off (on standby) at. Using Sleep Timer How Sleep Timer actually works Press SLEEP. Wait for about 5 seconds after specifying the time length. Maintenance Handling cassette tapes Handling discs Cleaning the unit Troubleshooting Symptom Cause Action Specifications