JVC XV-N412S Connecting to a TV with component jacks, Progressive scan video playback available

CConnecting to a TV with component jacks

You can enjoy picture of high-fidelity color reproduction by connecting the COMPONENT VIDEO OUT jacks on the player to your TV.

NOTES

•Connect “Y” to “Y,” “PB” to “PB” (CB), “PR” to “PR” (CR) correctly.

•When using the COMPONENT VIDEO OUT jacks, do not connect the S-VIDEO output jack on the player.

•If your TV has component video input jacks of BNC type, use an adapter which converts a pin jack to a BNC jack (not supplied).

Progressive scan video playback available

In the Progressive scanning mode, you can enjoy high quality picture with less flickers when the COMPONENT VIDEO OUT jacks are connected to a TV or monitor that supports the progressive video input.

Hint

Depending on the source material format, DVD VIDEO discs can be classified into two types; film source and video source (note that some DVD VIDEO discs contain both film source and video source). Film sources are recorded as 24-frame-per-second information, while (NTSC) video sources are recorded as 30- frame-per-second (60-field-per-second interlaced) information. When the player plays back a film source material, Progressive (uninterlaced) signals are created using the original information. When a video source material is played back, the unit interleaves lines between the interlaced lines on each to create the interpolated picture and outputs as the progressive signal.

		Set the PAL/NTSC selector to
		“PAL” or “NTSC” to match the
PAL	NTSC
		color system of your TV.
		(Change the selector position
		in stop mode or with no disc
		inserted.)

Selecting the 525i/625i - 525p/625p - REMOTE selector position

		If your TV equipped with
525P
	REMOTE
/625P		component jacks does not
525i		support the progressive
/625i		scanning mode:
		Set the 525i/625i - 525p/625p -
		REMOTE selector to “525i/
		625i.”
525P		• If your TV equipped with
	REMOTE
		component jacks supports
/625P

TV

			IN	PR
				PB
				Y
S-VID	EO			T
VID	EO
LEFT
AUD		IO
RIGHT

Red

Red

Blue

Green

The player

Preparations

525i		the progressive scanning
/625i		mode:
		Set the 525i/625i - 525p/
		625p - REMOTE selector to
		“525p/625p.”
		• If you want to select the
525P
	REMOTE
/625P		scanning mode between the
525i		interlace and progressive
/625i		modes (depending on the
		source condition, or when
		connecting more than one TV,
		etc.):
		Set the 525i/625i - 525p/
		625p - REMOTE selector to
		“REMOTE.”
		Thus you can select the mode
		from the remote control unit.

White

Component

video cable

5255pp

L

NT

AV

LINK

(not supplied)

RE

MOT

E

SC

COMPU

PR

/625i

PA

Red

/62

i

COMPONENT

525

VID

EO

Audio cable

Y

PB

Blue

COAX

LEFT

OUT

(not supplied)

IAL

PC

M/

S-VID

E

M

RIG

ST

REA

White

DIGITAL

O

PTIC

AL

AUD

IO

OUT

OUT

Red

Green

Activating the Progressive scanning mode using the remote control unit

When the player is turned on and the 525i/625i - 525p/625p - REMOTE selector is set to “REMOTE,” press and hold down VFP - PROGRESSIVE SCAN for a few seconds.

The scanning mode switches between the Progressive scanning and Interlaced scanning modes.

When the scanning mode is set to the Progressive mode, the [P] indicator lights up in the display window.

[DD]also turns on when Progressive scanned signals on a DVD VIDEO disc are directly output as they are from the player. Depending on the [PICTURE SOURCE] preference display and whether the current DVD VIDEO disc is film-source or video- source, the indicator that lights up in the display window differs, as shown in the table below.

Setting of [PICTURE	Source type of DVD VIDEO
SOURCE]
	Film source	Video source
AUTO	[DDP]	[P]
FILM	[DDP]	[DDP]
VIDEO (NORMAL)/	[P]	[P]
(ACTIVE)

5