Kathrein AON 65 manual „ Technical data of the antennas, „ Overview of the Kathrein antenna masts

_____________________________________________________________

Transmitter

Rotation 90° counter- clockwise

Î

Fig. 5: Horizontal alignment

„Technical data of the antennas

Transmitter

Writing legible

Cable outlet pointing slantwise down

Fig. 6: Vertical alignment

Type		AOI 65	AON 65	AOP 65
Order Number		212340	212344	212348
Channels		21-69	21-69	21-69
Gain	dB	7-9.5	8.5-13.5	9.5-15
Reception range	MHz	470-862	470-862	470-862
Full width at half maximum Horiz.	°	58-40	57-32	50-28
Vert.	°	90-65	70-44	59-31
Front-to-back-ratio	dB	20-25	21-26	22-28
Mast clamp range	Ø mm	22-60	22-60	22-60
Length	mm	410	814	1345
Wind load at 800 N/m2	N	40	59	106
Limiting wind load at 1100 N/m2	N	55	81	146
Packing unit/weight	P./kg	1/1.0	1/1.8	1/2.4
Packing unit dimensions	mm	490 x 420 x 75	825 x 500 x 75	840 x 500 x 95

„Overview of the Kathrein antenna masts

Type		ZSD 48	ZSF 47	ZSF 48	ZSH 47	ZSH 48	ZSH 59		ZSH 62 2)
Order Number		218380	218385	218381	218386	218394	218382		218383
Lenght L	m	2 x 2 = 4	2 x 2.5 = 5			2 x	3 = 6
Diameter D1/D2	mm			40/48				48/60
Cable entry points		3	-	3	-	3	5		5
Quality category (steel)		St 52	St 37	St 52	St 37	St 52	St 52		St 52
Wall thickness in clamping range	mm	2.5	2	2.5	2	2.5	2.5		4.5
Allowable bending moment 1),	5,0 m	-	-	-	320	850	1,150		1,950
Effectice length at 800 N/m2	4,0 m	-	500	1,040	430	960	1,280		(1,150)
	3,0 m	1170	540	1,080	-	-	-		2,120
									(1,280)
									-
Allowable bending moment 1),	5,0 m	-	-	-	160	700	900		1,700 (900)
Effectice length at 800 N/m2	4,0 m	-	390	920	300	840	1,080		1,960 (1080)
	3,0 m	1110	480	1000	-	-	-		-
Packing unit/weight	P./kg	1/11.4	1/11.3	1/14.2	1/13.1	1/17.8	1/20.5		1/37.5

1)The maximum allowable moment on the clamping point applies for the appropriate effectice length. The wind load absorption of the tube has already been allowed for. The bold values apply for an ordinary wind load (q = 800 N/m2). In case of increased wind load

(q = 1,100 N/m2), the reduced values apply.

According to EN 50083-1, the mast clamping length must be at least 1/6 of the mast length.

2)The technical data underlie the computation base according to DIN 4131.

If the sum of the antenna wind load moments exceeds the values put in parentheses (≙ 1,650 Nm at clamping point), a structural analysis is required, according to EN 50083, part 1.

www.kathrein.de

936.2595/B/1104/4.4e/ZWT Subject to technical changes.

KATHREIN-Werke KG ‚ Anton-Kathrein-Straße 1-3 ‚ P.O. Box 10 04 44 ‚ 83004 Rosenheim ‚ Germany ‚ Phone +49(0)8031 1840 ‚ Fax +49(0)8031 184306