Always unplug the power cord before making any adjustments or attaching accessories.
Be careful not to accidentally trip the power switch when setting the tool down or picking the tool up.
Always hold the tool by its insulated gripping surfaces when cutting in areas that may contain hidden live wiring. If the bit makes contact with a live wire, the metal parts of this tool may conduct enough electricity to seriously shock the user. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. Do not cut or break into existing walls or other blind areas where electrical wiring may exist. If this situation is unavoidable, disconnect all fuses or circuit breakers feeding this worksite.
Check to see that keys and adjusting wrenches are removed from the Rotary Tool before switching the tool “ON”. Keys or wrenches can fly away at high
velocity striking you or a bystander.
Do not use the Rotary Tool if it has been damaged, left outdoors in the rain, snow, wet or damp environments, or immersed in liquid.
Check the speed rating on all accessories. Accessories must never be run at a higher speed than they were designed to handle.
When using wire or bristle brushes, always wear protective gloves and a face shield. These brushes should never be run at speeds greater than 15,000
RPM.
Always run brushes at operating speed for a minute before using to eject loose wires and bristles. Be sure that the discharge is pointed away from you. Make sure no one is standing in front or in line with the brush.
Do not apply heavy pressure to wire or bristle brushes. This will only cause damage and/or personal injury. Brushes work best when applied lightly.
Do not use a wheel that may be damaged. If the tool or wheel is dropped, install a new wheel before continuing. Avoid bouncing and snagging the wheel as this may lead to cracking or chipping.
Do not sand or grind near flammable materials.
Handle sharp bits with care.
Never place hands near the spinning bit.
Never start the tool while bit is engaged in the material.
Always feed the bit into the material in the same direction that the chips are thrown.
If the bit becomes jammed in the workpiece, turn the tool off at the switch. Once all moving parts have come to a stop, unplug the tool and work the bit free.
Never lay the tool down until the motor has come to a complete standstill. A
running tool should not be left unattended.
Never touch the collet or bit immediately after use.
To prevent short circuits, clean the tool's vents regularly with compressed air. Do not alter or misuse tool.
This drill is not a dental tool. Do not use on the teeth of animals or humans.
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL | NAME | EXPLANATION | ||||||
|
| V | Volts | Voltage (Potential) | ||||
|
| A | Amperes | Current | ||||
| Hz | Hertz | Frequency (Cycles per Second) | |||||
| W | Watt | Power | |||||
| Kg | Kilograms | Weight | |||||
|
|
|
|
|
|
| Alternating Current | Type of Current |
|
|
|
|
|
|
| Direct Current | Type of Current |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Alternating or Direct Current | Type of Current |
|
|
|
|
|
|
| Earthing Terminal | Grounding Terminal |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| Class II Construction | Denotes Double Insulation |
| min | Minutes | Time | |||||
|
| s | Seconds | Time | ||||
| Diameter | Size of Drill Bits, | ||||||
|
|
|
|
|
|
|
| Grinding Wheels, etc. |
|
|
|
|
|
|
| No load speed | |
.../min | Revolutions per Minute | Revolutions, Surface Speed, | ||||||
|
|
|
|
|
|
|
| Strokes, etc. per Minute |
1,2,3, … | Ring Selector Settings | Speed, Torque or Position Settings | ||||||
7 | 8 |
