Kenmore 153.337072, 153.337002 owner manual Safety Precautions, Awarning

Safety Precautions

J	AWARNING	]
Improper installatio_lteration,		service or I
maintenance	can cause DEATH,	SERIOUS BODILY I

INJURY, OR PROPERTY DAMAGE. Refer to this manu- J al for assistance or consult your local Sears Service

Center for further nformat on.

AWARNING

WATER HEATERS EQUIPPED FOR ONE TYPE GAS ONLY: This water heater is equipped for one type gas only. Check the model rating plate near the gas control valve for the correct gas. DO NOT USE THIS WATER

HEATER WITH ANY GAS OTHER THAN THE ONE SHOWN ON THE MODEL RATING PLATE. Failure to use the correct gas can cause problems which can result in

DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. If you have any questions or doubts consult your gas supplier or local utility.

_WARNING

INSTALLATIONS IN AREAS WHERE FLAMMABLE LIQ-

UIDS (VAPORS) ARE LIKELY TO BE PRESENT OR STORED (GARAGES, STORAGE, AND UTILITY AREAS,

ETC): Flammable liquids (such as gasoline, solvents, propane (LP) or butane, etc.), all of which emit flammable vapors, may be improperly stored or used in such areas. The gas water heater pilot light or main burner can ignite such vapors. The resulting flashback and fire can cause death or serious burns to anyone in the area, as well as property damage.

If installation in such areas is your only option, then the

installation must be accomplished in a way that the pilot flame and main burner flame are elevated from the floor

at least 18 inches. While this may reduce the chances of

flammable vapors from a floor spill being ignited, gasoline and other flammable substances should never be stored or

used in the same room or area containing a gas water heater or other open flame or spark producing appliance. NOTE: Flammable vapors may be drawn by air currents from other areas of the structure to the appliance.

_,WARNING

If this water heater will be used in beauty shops, barber shops, cleaning establishments, or self-service laundries

with dry cleaning equipment, it is imperative that the water heater or water heaters be installed so that com-

bustion and ventilation air be taken from outside these

areas. Refer to the "Locating The New Water Heater" section of this manual and also the latest edition of the

National Fuel Gas Code, ANSI Z223.1, also referred to as

NFPA 54 for specifics provided concerning air required.

AWARNING1

Afire can start if combustible materials such as clothing, cleaningmaterials, or flammable liquidsare placed against

or next to the water heater.

AWARNING

At the time of manufacture this water heater was pro-

vided with a combination temperature-pressures relief valve certified by a nationally recognized testing labora- tory that maintains periodic inspection of production of

listed equipment or materials, as meeting the require-

ments for Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems, and the latest

edition of ANSI Z21.22 and the code requirements of

ASME. If replaced, the valve must meet the require- ments of local codes, but not less than a combination

temperature and pressure relief valve certified as meet-

ing the requirements for Relief Valves and Automatic

Gas Shutoff Devices for Hot Water Supply Systems, ANSI Z21.22 by a nationally recognized testing laborato- ry that maintains periodic inspection of production of listed equipment or materials.

The valve must be marked with a maximum set pressure not to exceed the marked hydrostatic working pressure of the water heater (150 Ibs./sq. in.) and a discharge capacity not less than the water heater input rate as shown on the model rating plate. (Electric heaters - watts divided by 1000 x 3415 equal BTU/Hr. rate.)

Your local jurisdictional authority, while mandating the

use of a temperature-pressure relief valve complying with ANSI Z21.22 and ASME, may require a valve model different from the one furnished with the water heater.

Compliance with such local requirements must be satis- fied by the installer or end user of the water heater with

a locally prescribed temperature-pressure relief valve installed in the designated opening in the water heater in place of the factory furnished valve.

For safe operation of the water heater, the relief valve

must not be removed from it's designated opening or plugged.

The temperature-pressure relief valve must be installed directly into the fitting of the water heater designatedxf_;_. the relief valve. Position the valve downward and provide tubing so tha_any discharge will exit only within 6finches,

above,	or at	any	dist:_ow-'_"_s_P_uc-Tur'P-_11o0r.		Be
certain	that	no	contact_is.mad_e	e_ lect_ical"

_art. The discharge opening must not be blocked or

reduced n s ze under-_an_es_Excessve length, over 30 feet, or use of more than_four'e_lbowscan

cause restriction			and redu'_e-_-_--dffch'arge capaLctty.-of
the valve.				,. - _ -
No	valve	or other	obstruction is to	b-e--I_lacec]-b_tween
the	relief	valve and the _k,-JDo-n_t		t_tibifig

directly to discharge drain unless a 6" air gap is provided.

To prevent bodily injury, I_r_rd t_fife,-or-propertydam- age, the relief valve must be allowed to discharge water in quantities should circumstances demand. If the dis- charge pipe is not connected to a drain or other suitable means, the water flow may cause property damage.

The Discharge Pipe:

•Must not be smaller in size than the outlet pipe size of

the valve, or have any reducing couplings or other restrictions.

•Must not be plugged or blocked.

•Must be of material listed for hot water distribution.

•Must be installed so as to allow complete drainage of

both the temperature-pressure relief valve, and the discharge pipe.

•Must terminate at an adequate drain.

•Must not have any valve between the relief valve and tan_