Kenmore 22-46262 specifications Order, 30 Min, Locate Cabinet, Door Open+

30-Inch Manual-Clean Electric Coil Slide-Ins

22-46262

page 2 of 2

For existing 29" cutout width
opening, you must call the Sears Service	30" Min.
Center for optional thinner side panels.
Also you must prepare the countertop		13"
edge as shown in “Counterdepth
Preparation”.
Shave Raised	30" Min.*
Edge To Clear			18" Min.

311/2" Wide Cooktop.

1 1/2" Max.		30"†
		±1/16"
	36 5/8" Max.	Approx. 1 7/8"
	35 5/8" Min.
	21 3/4"	24" Min.
	min.**
Locate Cabinet	22 1/8"
	max.

Doors 1" Min. From

Cutout Opening

Grounded Junction Box or Wall Outlet Should Be Located 8" to 17" (20.3 - 43.2 cm) From Right of Cabinet and 2" to 4" From Floor

Do not pinch the power supply cord between the range and the wall. Do not seal the range to the side cabinets.

*Note: 24" min. clearance between the cooktop and the bottom of the cabinet when the bottom of the wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than No. 28 MSG sheet metal, 0.015" stainless steel, 0.024" aluminum, or 0.020" copper. 30" min. clearance when the cabinet is unprotected.

**Note: Minimum cutout depth is increased to 24" with optional backguard.

†Note: To avoid cooktop glass breakage for cutout width of more than 30 1/16", make sure appliance is centered in the counter opening while pushing

into it. Raise leveling legs at maximum position, insert the appliance in the counter and then level. Make sure the unit is supported by the leveling legs and not by the smoothtop glass itself.

††For cutouts below 22 7/8”, appliance will slightly show out of the cabinet. +Allow at least 19 1/4" clearance for door depth when it is open.

COUNTERTOP PREPARATION

The cooktop sides of the range fit over the cutout edge of your countertop.

Countertop must be level.

If you have a square finish (flat) countertop, no countertop preparation is required. Cooktop sides lay directly on edge of countertop.

Formed front-edged countertops must have molded edge shaved flat 3/4" from each front corner of opening.

Tile countertops may need trim cut back 3/4" from each front corner and/or rounded edge flattened.

If the existing cutout width is greater than 30 1/16", reduce the 3/4" dimension.

	Min.	3/4"
	cutout
	width	Formed or tiled
	31 1/2"
		countertop
		trimmed 3/4" back
	3/4"	at front corners of
		countertop opening.
		28 5/16"
	22 7/8" min.††	21 3/4"
	23 1/4" max.	31 1/2"
	1 1/8"
	21 3/4" min.	35 5/8" -
CABINET		36 3/8"
FRONT	22 1/8" max.	Door Open+

Side Panel

30"

22-49614,	RANGE CORD REQUIRED			22-49624,
22-49616	Order	Wire	Length	22-49626
	22-49614	3	4 ft.
	22-49616	3	6 ft.
	22-49624*	4	4 ft.
	22-49626*	4	6 ft.

*Complies with 1/1/96 NEC code revision for new construction and remodeling

07806

Because of our continuous program of product improvement, Sears reserves the right to change materials and specifications without notice. Consult installation instructions packed with the product for final dimensional data. For complete warranty information, contact your local Sears Contract Sales Account Manager.

All ranges are equipped with an Anti-Tip device. The installation of this device is an important, required step in the installation of the range.

22-46262.PDF

Effective 05/31/06 Rev. 1