Location Requirements
Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”
Your washer can be installed in a basement, laundry room, closet, or recessed area. See “Drain System.”
IMPORTANT: Do not install or store the washer where it will be exposed to the weather.
Proper installation is your responsibility.
You will need:
■A water heater set to deliver 120°F (49°C) water to the washer.
■A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”
■Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill valves, and water pressure of
■A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.
■A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kgs).
Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See “Washer Care” for winterizing information.
Installation spacing for recessed area and closet installations
The following spacing dimensions are recommended for this washer. This washer has been tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:
■Additional spacing should be considered for ease of installation and servicing.
■Additional spacing should be considered on all sides of the washer to reduce noise transfer.
■For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
■Companion appliance spacing should also be considered.
|
| 3"* |
14"* max. | 48 in.2 * | (7.6 cm) |
(35.6 cm) |
| |
17"* | (310 cm2) |
|
|
| |
(43.2 cm) |
|
|
| 24 in2.2* | 3"* |
| (155 cm ) | (7.6 cm) |
|
|
1" |
|
|
|
| 27¹⁄₂" |
|
|
| 1" |
|
| 1"* |
|
| 27" |
|
| 5"* |
|
|
|
(2.5 cm) |
| (69.9 cm) |
| (2.5 cm)(2.5 cm) (68.6 cm) (12.7 cm) | |||||||||||||||||
|
|
|
|
| A |
|
|
|
|
|
|
|
|
| B |
|
|
| C | ||
A. Front view
B. Side view
C. Closet door with vents
* Required spacing
Drain System
The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See “Tools and Parts.”
Standpipe drain system—wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum
The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (244 cm) from the bottom of the washer.
(39")
99 cm
AB
Laundry tub drain system (view C)
The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39" (99 cm) above the floor and no higher than 96" (244 cm) from the bottom of the washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be purchased separately. See “Tools and Parts.”
The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.
39" | 28" |
(71 cm) |
(99 cm)
CD
6
