INSTALLATION
LOCATION OF THE PORTABLE AIR CONDITIONER
1.Select a location near a window and electrical outlet.
2.Position the unit in a flat, spacious location
with a minimum of one foot of clearance (30 cm) between the air outlets and any
wall or pieces of furniture.
3. If placing the unit outside of the room to be cooled, position it on a flat solid surface, preferably in a space with overhead shielding from rain and the direct rays
of the sun. Do not operate the unit in extremely moist areas such as a sauna.
WINDOW KIT INSTALLATION
The Window Kit (included) contains three sliding pieces, and can be adjusted to fit most standard vertical and horizontal windows (see Figs. 1 & 1a). For very wide windows, use all three pieces. For very narrow windows, you may have to cut down the end of the piece with the hose attachment hole. Do not cut into the hole.
EXHAUST HOSE CONNECTION
SAFETY PLUG
This product is equipped with an LCDI (Leakage Current Detection and Interruption) safety plug. If power shuts off, unplug from the electrical outlet and make sure the cord is undamaged. If the cord is damaged, return the unit to a Sears Service Center for repair before using it again.
TO TEST THE SAFETY PLUG
1.Connect the power plug to an electrical outlet.
2.The power plug has two buttons located on the top. One button is marked “TEST” and the other is marked “RESET”. Press the “TEST” button; you will hear a click as the “RESET” button pops out.
3.Press the “RESET” button; you will hear a click as the button engages.
4.The power supply cord is now energized and supplying electricity to the air conditioner (it is indicated by a light on the plug head).
•Under no circumstances should this device be used to turn the unit on or off.
•The “RESET” button must always be pushed in (engaged) for correct operation.
•The power supply cord must be replaced if it fails to reset when the “TEST” button is pushed in.
CONTROL PANEL
The exhaust hose must be attached to the appropriate side of the unit given the desired application, either cooling or heating (see Operating Instructions). When changing applications, switch the adjustable air vent and exhaust hose holder (hose can remain attached) to the opposite sides of the unit.
Fig. 1 | Fig. 1a | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Window kit |
| Window kit |
|
Min: 19 in. |
| Min: 19 in. |
|
(48 cm) |
| (48 cm) |
|
Max: 50 in. |
| Max: 50 in. |
|
(127 cm) | Vertical Window | (127 cm) | Horizontal Window |
|
|
10
(5)
(2) (7) (1)
(3) (6)
(8)
(4)
1. POWER 
Press this button to switch the unit on or off.
2. MODE
Press this button to select between Cooling ( ), Heating (
) or Dehumidifying ( 
) mode.
NOTE: To change display between °F and °C, press the MODE button for 10 seconds with the power off and unit plugged in (Standby Mode). You will hear a beep when the change occurs.
3. TEMP+ 
•Pressing this button in cooling mode increases the desired room temperature setting by 1°F (1°C) up to a maximum setting of 86°F (30°C).
•Pressing this button in heating mode increases the desired room temperature setting by 1°F (1°C) up to a maximum setting of 77°F (25°C).
11
