Kenmore 580.72184 owner manual Features, Using, The Air Conditioner

Models: 580.72184

1 23
Download 23 pages 59.29 Kb
Page 10
Image 10
FEATURES

FEATURES

 

 

 

 

 

USING

THE AIR CONDITIONER

 

 

 

 

 

 

 

_]_]_

 

To reduce the risk of fire, electric

 

 

 

 

 

 

 

shock, or injury to persons, read the important

 

 

 

 

 

 

 

SAFETY instructions section before operating this

 

 

 

 

 

 

 

appliance

 

 

 

 

 

 

 

 

 

To begin operating the air conditioner after

 

 

 

 

 

 

 

installation,

follow these steps:

 

 

 

 

 

 

 

1. Plug in the air conditioner.(To prevent electrical

 

 

 

 

 

 

 

hazards, do not use an extension cord or an

 

 

 

 

 

 

 

adapter plug.)

 

 

 

 

 

 

 

 

2, Set the exhaust vent to the CLOSE position.

 

 

 

 

 

 

 

3, Set the TEMP Control to the coolest setting,

 

 

 

 

 

 

 

4. Set the MODE Control at the highest COOL level.

1

14

5

 

4

63

213

5. Adjust the louver for comfortable air flow.

 

6, Once the room has cooled, adjust the TEMP and

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MODE control to the setting you find most

 

 

 

 

 

 

 

comfortable.

 

 

 

 

 

 

 

 

NOTE : I1=the air conditioner is turned off, wait 3

 

 

 

 

 

 

 

minutes before restarting. This allows pressure

 

 

 

 

 

 

 

inside the compressor to equalize. Failure to wait 3

 

 

 

 

 

 

 

minutes before restarting may cause inefficient

 

 

 

 

 

 

 

operation.

 

 

 

 

 

 

 

 

 

If you move the TEMP Control to a warmer, then

 

 

 

 

 

 

 

immediately back to a cooler setting, the unit will

 

 

 

 

 

 

 

shut off. Wait 3 minutes before restarting,

 

 

 

10 11

9

12

 

VENT

CONTROL

 

 

 

 

 

The Vent Control allows the air conditioner to either

 

 

 

 

 

FIG. 22

 

 

 

 

 

recirculate inside air (CLOSE) or exhaust air to the

 

 

 

 

 

 

 

1. Cabinet

 

 

 

 

 

 

outside (OPEN). (FIG. 23)

 

 

 

 

 

 

o The CLOSE position is used when maximum

 

 

 

 

 

 

 

2. Vertical

Air

Direction

Louvers

 

 

 

cooling is desired.

It may also be used for air

3. Cool Air Discharge

 

 

 

 

recirculation without cooling when the air

 

 

 

 

conditioner is set in the FAN position,

4. Inlet Grille

 

 

 

 

 

 

 

 

 

 

The OPEN position

removes stale air from the

 

 

 

 

 

 

 

5. Air Filter

 

 

 

 

 

room

and exhausts

it to the outside. Fresh air is

6. Control

Board

 

 

 

 

drawn into the room through your home's normal

 

 

 

 

air passages.

 

7. Power

Cord

 

 

 

 

 

 

 

 

 

 

 

The OPEN

or CLOSE position can be used with

8. Evaporator

 

 

 

 

 

any fan selection.

 

 

 

 

 

 

 

 

 

 

9.Condenser

10.Compressor

11.Base pan

12.Brace

13.

Upper Guide

PULL

 

14.

Curtain

 

FIG. 23

-10-

Page 10
Image 10
Kenmore 580.72184 owner manual Features, Using, The Air Conditioner