Kenmore 625.38156 owner manual Connect RED Tube to Reverse Osmosis Faucet

	3/8" black
water supply	tubing
fitting

cX9

i IOT COLD

/

sink p-trap

NOTE: Tubing lengths should allow for the removal of the assembly from the hanger washers for servic- ing. If tubing lengths are shortened for nearer

appearance, it may be necessary to keep the assem- bly on the hanger washers for service.

NOTE: Codes in the state of Massachusetts require installation by a licensed plumber and do not permit the use of saddle valves. If you live in the state of

Massachusetts, review plumbing code 248-CMR of

the Commonwealth of Massachusetts before pro- ceeding with the installation.

3/8" yellow tubing

tubing

NOTE:	Tube colors match	onnector
Collet	colors

Tube

Connections

Figure

21

CONNECT

YELLOW

TUBE

TO

STORAGE

TANK

CONNECT

BLUE

TUBE

TO

REVERSE

OSMOSIS

1.

Locate the

yellow

tube.

One

end

is attached

to the

Reverse

ASSEMBLY

Osmosis

filter

assembly.

1.

Locate

the

blue tube.

One

end

is

attached

to

the faucet.

2.

Run

the

other

end

of the

yellow

tube to

the fitting

on top of

2.

Run

the

other

end of the

3/8"

blue

tube to

the blue collet

on

the

storage

tank.

See

Figure

21.

the

right

side

of the Reverse Osmosis

filter

assembly.

3.

Cut

tube square

and

to

length.

See Figure

17.

3.

Cut

tube

square

and

to length.

See

Figure

17.

4.

Do

not connect

at

this time. This

will occur in the

sanitizing

4.

Insert

all

the

way

into the

fitting.

See

Figures

18A & 18B.

step.

5.

Pull

on the

tube

to be

sure

it's

held

firmly

in

the fitting.

CONNECT

GREEN

TUBE

TO

COLD

WATER

CONNECT

BLACK

TUBE

FROM

REVERSE OSMOSIS

SUPPLY

PIPE

FAUCET

TO

DRAIN

ADAPTER

1.

Run

one

end of the 1/4" green

tube

to the

fitting on

the water

1.

Locate

the

30" length

of

3/8" black

tube. One

end is attached

supply pipe. See Figure 21.

to the faucet. Figure 21.

2.

Cut

tube

square

and

to length.

See

Figure

17.

2.

The

other

end needs

to

be

attached

to

the

black collet

on

the

3.

Connect

to

saddle

valve.

This

is a compression

fitting.

sink

drain

adapter.

4.

Run

the

other

end

of the

green

tube

to green collet

to the fit-

3.

Cut

this

tube

as needed

to

route

in

as

straight

of a run

as

ting on the left side of the Reverse Osmosis filter assembly.

possible,

without

loops,

dips,

low spots or

kinks.

5.

Cut

tube

square

and

to length.

See

Figure

17.

4.

Cut

the end of the tube

square.

See Figure

17.

6.

Insert all the way

into the

fitting.

See Figures

18A & 18B.

5.

Insert

all

the

way

into

the

fitting.

See Figures

18A & 18B.

7.

Pull

on

the

tube

to be

sure

it

is held

firmly

in

the fitting.

6.

Pull

on the

tube to be

sure

it is held

firmly

in

the fitting.

CONNECT RED TUBE TO REVERSE OSMOSIS

FAUCET

The red tube cormection was completed in the faucet assembly steps.

Questions? Call The Kenmore Water Line 1-800-426-9345or visit KenmoreWater.com

15