Adding Items During a Cycle
You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is still closed, you can add items.
■Turn the TURBOZONE™ wash option off if not loading items for this option. Always use the Heavy Soil detergent fill recommendation with TURBOZONE™ wash option. (See “How much detergent to use” in “Detergent Dispenser” section.)
To add items
1.Open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door. The Start/Resume light will flash.
2.Open the door. If the detergent dispenser cover is still closed, add the item.
3.Close the door firmly until it latches. The Start/Resume light will flash.
4.Press START/RESUME.
IMPORTANT: If Lock On is selected, turn off the lock (see Lock On section in “Option Selections”), or the Start/Resume light will continue to flash.
Option Selections
You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off, or select a different option if desired.
You can change an option anytime before the selected option begins. For example, you can press an unheated drying option anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when you press START/RESUME, the dishwasher runs the last full wash cycle and options.
TURBOZONE™ wash option
Select this option to activate the TURBOZONE™ spray jets and provide intensified water spray to the back of the lower dishrack. The TURBOZONE™ wash option provides a concentrated wash action to pans, casseroles, etc. with tough food soil.
This option may add heat and wash time to the cycle.
NOTE: TURBOZONE™ is an option with the SMART WASH™, Pots Pans, and Normal Wash cycles.
IMPORTANT:
■Load pans, casserole dishes, etc. facing the TURBOZONE™ spray jets in the back of the lower dishrack. Tip items toward the rear of the dishrack to maximize coverage. Only one row of items may face the TURBOZONE™ spray jets. Stacking, overlapping, or nesting items will keep the TURBOZONE™ spray jets from reaching all of the surfaces.
■To maximize spray coverage, avoid placing silverware basket or other items to interfere with the rotation of the TURBOZONE™ spray jets.
Side view of TURBOZONE™ wash area
Hi Temp
Select this option to increase the water temperature during the wash portions of the cycle. Hi Temp wash raises the water temperature to 145ºF (63ºC), in the main wash. Heating the water helps improve washing results. Hi Temp wash is useful when loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: Hi Temp wash is an option with the SMART WASH™, Pots Pans, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse to approximately 155°F (68°C). Sani Rinse adds heat and time to the cycle. This high temperature rinse sanitizes your dishes and glassware in accordance with NSF/ANSI Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMART WASH™, Pots Pans, and Normal Wash cycles. Only these sanitization cycles have been designed to meet the NSF/ANSI requirements.
Heated Dry
The Heated Dry option in combination with rinse aid will give you excellent drying results. The energy to use Heated Dry costs pennies per cycle. Heated Dry is on when the light is lit on the Heated Dry button. Be sure to load plastic items in the upper rack to avoid damage.
You may turn off the Heated Dry option by pressing HEATED DRY so that the light goes off. However, you will have items in your dishload that will not be dry at the end of the cycle.
NOTE: The Heated Dry option is used in all cycles except Fast Wash and Quick Rinse.
17
