TROUBLESHOOTING
First try the solutions suggested here and possibly avoid the cost of a service call...
■White residue on the front of the access panel
Dishwasher is not operating properly
■Dishwasher does not run or stops during a cycle Is the door closed tightly and latched?
Is the right cycle selected? Refer to the “Cycle Selection Charts.”
Is there power to the dishwasher? Has a household fuse blown, or has a circuit breaker tripped? Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.
Has the motor stopped due to an overload? The motor automatically resets itself within a few minutes. If it does not restart, call for service.
Is the water shutoff valve (if installed) turned on?
It is normal for certain cycles to repeatedly pause for several seconds during the wash cycle.
■START/RESUME light is flashing
Was the door opened during the cycle, or was the power interrupted? The Start/Resume light will flash when the door is opened during a cycle, or may flash if the power is interrupted. Press START/RESUME to resume the cycle. Make sure the door is fully closed and latched.
NOTE: On top control models, if the door is not closed within 3 seconds of pressing Start/Resume, press START/RESUME again.
■Clean light is flashing
The dishwasher has malfunctioned. Call for service.
■Dishwasher will not fill
Is the overfill protection float able to move up and down freely? Press down to release.
■Dishwasher seems to run too long
Is the water supplied to the dishwasher hot enough? The dishwasher runs longer while heating water. Refer to the “Dishwasher Efficiency Tips” section.
A delay automatically occurs in some wash and rinse cycles until the water reaches the proper temperature.
■Water remains in the dishwasher Is the cycle complete?
Was the disposer knockout plug removed during installation? (See “Install the drain hose” in the Installation Instructions.)
■Detergent remains in the covered section of the dispenser
Is the cycle complete?
Is the detergent
Is the bottom rack installed properly with the bumpers (on some models) in the front? Refer to the “Parts and Features” section. Reinstall the rack if necessary.
Was too much detergent used? Refer to the “Detergent Dispenser” section.
Is the brand of detergent making excess foam? Try a different brand to reduce foaming and eliminate buildup.
■Odor in the dishwasher
Are dishes washed only every 2 or 3 days? Run a rinse cycle once or twice a day until you have a full load.
Does the dishwasher have a new plastic smell? Run a vinegar rinse as described in the section “Spotting and filming on dishes.”
■Condensation on the kitchen counter (built-in models)
Is the dishwasher aligned with the countertop? Moisture from the vent in the dishwasher console can form on the counter. Refer to the Installation Instructions for more information.
■Bottom rack does not fully slide into the dishwasher
Check to see if items loaded for TURBOZONE™ wash option have shifted. Reload to keep items from interfering with spray jets or spray arm. (See “Loading Bottom Rack.”)
Dishes are not completely clean
■Food soil left on the dishes
Is the dishwasher loaded correctly? Refer to the “Dishwasher Loading” section.
Is the water temperature too low? For best dishwashing results, water should be 120°F (49°C) as it enters the dishwasher. Refer to the “Dishwasher Efficiency
Tips” section.
Did you use the correct amount of fresh detergent? Use recommended dishwasher detergents only. Refer to the “Detergent Dispenser” section. Detergent must be fresh to be effective. Store detergent in a cool, dry area. Heavy soil and/ or hard water generally require extra detergent.
Do you have hard water? You may need to increase the amount of detergent you are using. Refer to the “Detergent Dispenser” section. Also, you may need to switch to a detergent with a phosphorus content of 8.7%.
Is detergent caked in dispenser? Use fresh detergent only. Do not allow detergent to sit for several hours in a wet dispenser. Clean dispenser when caked detergent is present.
Is the pump or spray arm clogged by labels from bottles and cans?
Is the home water pressure high enough for proper dishwasher filling? Home water pressure should be 20 to
120 psi (138 to 828 kPa) for proper dishwasher fill. If you have questions about your water pressure, call a licensed, qualified plumber.
Are high suds slowing the wash arm? Do not use soap or laundry detergents. Use recommended dishwasher detergents only.
20
