Kenmore 72785 5/8--6,4,71/4,5, Disconnect Sink Drain, Disassemble New Disposer Mounting Assembly

CHECK	INSTALLATION	DIMENSIONS
A. Disposer Height
B. Distance from bottom of sink		]	B
bowl to centerline of discharge
outlet. (Add 1/2" when stainless
steel sink is used.)		A,
C: Distance from centerline of		L
the discharge outlet to end
of discharge	tube.

D: D_sposer Width

D---'------

E:Distance from disposer vertical centerline to centerline of P-trap connection.

F:Centerline of disposer discharge to centerline at waste pipe entering wall. (Dimension "F" must be greater than 1/4" to prevent standing water in disposer.)

If replacing an	existing disposer,	skip ahead	to Instruction	6.	]
If this is a first	time installation,	continue with	Instruction	2.	/

DISCONNECT SINK DRAIN

1.Loosen nut (A) at top of "P-trap" with pipe wrench (see Figure 2-1).

2.Loosen nut (B) at top of extension pipe. Remove extension pipe.

3.Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply penetrating lubricant

4.Push s_nk flange up through sink hole and remove it (see Figure 2-2).

5.Clean sink flange area of any putty or other debris.

DISASSEMBLE NEW DISPOSER

MOUNTING ASSEMBLY

1.Insert wrenchette (or screwdriver) into one mounting lug and hold lower mount- ing ring securely with one hand (see Figure 3-1). With your other hand, turn mounting assembly counterclockwise to remove mounting assembly from lower mounting ring

2.Turn mounting assembly over (see Figure 3-2) and loosen three mounting

screws (A) until you can access snap ring (B).

3Use screwdriver to pry snap ring off of sink flange. Mounting assembly will now come apart.

INSTALL FLANGE IN SINK HOLE

1.Roll 1/4 pound (4 oz.) of non-hardening plumber's putty to make 3/4" thick rope to seal around sink flange.

2.Apply putty evenly around sink hole (see Figure 4-1).

3.Press sink flange slowly but firmly into sink drain hole to seat evenly on putty

(see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge of sink hole.

_k CAUTION

Do not use plumber's putty on any other disposer connection - it may harm disposer and cause property damage.

1odel		A	B	C		b	E
010/6012	11	3/8"	6"	4"	6 5/16"		5"
01116013	12	5/8"	6"	4"	6 5/16"		5"
0552	12	5/8"	6"	4"	7 1/4"		5"
		5/8'--6,' 4,'71/4,'5"
_3/4"			611/16"	4'=._ 81/2'.=_=53/4'_
		3/4"	6 11/16"	4"	8	1/2"	5 3/4"
0559* _1157/8"			9 7/16"	4"	7	1/2"	5 3/4"
--		"	6"	4"	7	1/4"	5"
			6"	4"	7	1/4"	5"

_'"Indicates Batch Feed Model

J

" - r " /_

2-12-2

/!i

3-13-2

4-14-2

ATTACH UPPER MOUNTING ASSEMBLYTO SINK FLANGE

You may wish to place a we=ghted object in the sink to hold the sink flange in place. (Place a towel under object in sink to prevent scratching ) Reference F=gure 5-1 for part identification.

1	Working from	under sink, slip fiber gasket and 4 Tighten three mounting screws up to sink
	metal backup	ring over	sink flange.		until mounting assembly is seated tightly
2	Holding fiber	gasket and backup ring in place,			and evenly against sink.
	shp mounhng	nng over	s_nk flange	so it seats	* Placing a thick, wide rubber band around
	against backup nng				the sink flange (above the snap ring
3	W_th fiber gasket, backup nng, and mounting				groove) may help hold parts Jnplace _,,hde
	ring hght to S,F.'.ottom,		shde snap	r',ngcnto	tnstalhng snap ring. (Remember to rer'nove
	s_nk flange until _tpops		{nto groove	on flange'.	rubber band after snap ring is installed.) '

If you are replacing an existing disposer, go to Instruction 6 If this is a first time _nstallahon, 1

skip ahead Io Instruction 7 J

Sink Flange

Fiber Gasket /

Backup R=ng __ _._'_).

MountEng RLng __ X_-@

Snap Ring O

5-1