Installation

446mm

432mm

 

 

 

 

 

 

 

 

 

 

 

157 mm

252 mm

265 mm

 

 

100

150

 

100

 

1

100

 

 

1

 

 

 

 

 

70

150

2

0.5

70

150

2

0.5

 

 

4/3/2channel Power Amplifier

70

 

 

 

3

0.3

 

 

3

0.3

 

 

50

200

50

200

(MIN)54

0.2(MAX) 50

200

(MIN)54

0.2(MAX)

 

 

 

 

 

LPF

 

HPF

 

INPUT

HPF

 

 

INPUT

 

 

 

 

FREQUENCY(Hz)

FREQUENCY(Hz)

SENSITIVITY(V)

FREQUENCY(Hz)

SENSITIVITY(V)

 

 

HPF OPERATION

LPF OPERATION

 

 

 

B ch

 

 

 

A ch

 

 

 

 

 

 

 

FILTER

AMP CONT

ISF OPERATION

HPF

OPERATION

 

 

 

 

 

 

 

 

 

 

 

 

 

Ø6

 

Accessories

Part name

External View Number of Items

Self-tapping screws

4

(ø5 × 18 mm)

 

Hexagon socket head cap screw

4

(M4 × 8 mm)

 

Cover

1

Terminal cover (Power terminal)

1

Hexagon Wrench

1

Duct

Hexagon socket

 

head cap screw

 

(M4 × 8 mm)

Cooling fan

Cover

Installation board, etc. (thickness : 15 mm or more)

Hexagon Wrench

Cooling fan

Self-tapping screw (ø5 × 18 mm)

Installation procedure

Since there are large variety of settings and connections possible according to applications, read the instruction manual well to select the proper setting and connection.

1.Remove the ignition key and disconnect the negative -terminal of the battery to prevent short circuits.

2.Set the unit according to the intended usage.

3.Connect the input and output wires of the units.

4.Connect the speaker wires.

5.Connect the power wire, power control wire and grounding wire following this order.

6.Install the installation fittings in the unit.

7.Attach the unit.

8.Install the terminal cover.

9.Connect the negative -terminal of the battery.

2CAUTION

•Do not install in the below locations;

(Unstable location, In a location that interferes with driving, In a location that gets wet, In a dusty location, In a place that gets hot, In a place that gets direct sunlight, In a location that gets hit by hot air)

•Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged.

•Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit.

•The surface temperature of the amplifier will become hot during use. Install the amplifier in a place where people, resins, and other substances that are sensitive to heat will not come into contact with it.

•This unit has cooling fans to decrease the internal temperature. Do not mount the unit in a place where the cooling fan and ducts of the unit are blocked. Blocking these openings will inhibit the cooling of the internal temperature and result in malfunction.

•When making a hole under a seat, inside the trunk, or somewhere else in the vehicle, check that there is nothing hazardous on the opposite side such as a gasoline tank, brake pipe, or wiring harness, and be careful not to cause scratches or other damage.

•Do not install near the dashboard, rear tray, or air bag safety parts.

•The installation to the vehicle should securely fasten the unit to a place in which it will not obstruct driving. If the unit comes off due to a shock and hits a person or safety part, it may cause injury or an accident.

•After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally.

English 3