Connection
* Commercially available parts
2WARNING
To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal.
2CAUTION
•If sound is not output normally, immediately turn power off and check connections.
•Be sure to turn the power off before changing the setting of any switch.
•If the fuse blows, check wires for shorts, then replace the fuse with one of the same rating.
•Check that no unconnected wires or connectors are touching the car body. Do not remove caps from unconnected wires or connectors to prevent short circuits.
•Connect the speaker wires to appropriate speaker connectors separately. Sharing the negative wire of the speaker or grounding speaker wires to the metal body of the car can cause this unit to fail.
•After installation, check that the brake lamps, winkers, and wipers work properly.
CENTER UNIT (CD receiver, etc.)
Lead terminal*
Power control wire
30 | 30 |
|
| FUSE(30A⋅2) | POWER |
Terminal cover 
Battery wire*
Protective Fuse*
RCA cable*
RCA cable ground
terminalB channel input
GND |
|
| A channel |
|
| input | |
|
|
| |
| 5 |
|
|
4 | 67 |
| |
23 |
| 8 |
|
10 | 9 |
| |
|
| ||
ID NUMBER TO H/U | REMOTE RESET | ||
A channel
Right speaker
A channel
Left speaker
B channel
Right speaker
B channel
Left speaker
■Bridged Connections
A channel
Speaker (Bridged)
Battery | Ground wire* |
B channel Speaker (Bridged)
■LX-Bus connection
CENTER UNIT
Power control wire
30 | 30 |
|
| FUSE(30A⋅2) | POWER IN |
Master amplifier
Extension wire*
30 | 30 |
|
| FUSE(30A⋅2) | POWER IN |
Slave amplifier 1
30 | 30 |
|
| FUSE(30A⋅2) | POWER IN |
Slave amplifier 7
To Kenwood disc changer/ | Set the ID number of the Master amplifier to "0". | ||||||
External optional accessory | You can connect up to 7 Slave amplifiers. Assign them ID numbers "1" | ||||||
|
|
|
|
|
| ||
|
|
|
|
|
| to "7" and do not duplicate them. | |
Control cable | 2 CAUTION | ||||||
• Do not connect 2 Master amplifiers to the Center Unit. If done, you | |||||||
(option) | |||||||
cannot control all amplifiers connected to the Center Unit. | |||||||
|
|
|
|
|
| ||
|
|
|
|
|
| • The LX AMP and the sensor unit cannot be connected | |
|
|
|
|
|
| simultaneously. You must connect any of them at a time. | |
|
|
|
|
|
| NOTE | |
|
|
|
| 5 |
| • The total length of | |
|
|
| 4 | 67 | (46 ft) maximum. If the cable length exceeds this limit, you cannot | ||
|
| 23 |
| 8 | |||
|
| ID NUMBER TO H/UREMOTE RESET | |||||
|
|
| 1 | 0 | 9 |
| |
"0" |
| 5 | 6 |
| control amps from the Center Unit. | ||
4 |
| • If you assign the same ID number to multiple amplifiers, they | |||||
2 | 0 | 9 | 8 | ||||
1 |
|
| |||||
| 3 |
|
| 7 |
| ||
| ID NUMBER | malfunction when you operate any of them from the Center Unit. | |||||
| • If you assign ID number "8" or "9" to a Slave amplifier, it is not | ||||||
|
|
|
|
|
| ||
recognized by the Center Unit. | |||||||
RCA cable* | |||||||
|
|
|
|
|
| ||
|
|
|
| 5 |
|
|
|
| 4 | 67 |
|
|
| 23 | 8 |
| |
|
|
| 10 | 9 |
|
|
| ID NUMBER TO H/U | RESET | ||
"1" – "7" | 4 | 5 | 6 |
| |
1 | 0 | 9 |
| ||
| 3 |
|
| 7 |
|
| 2 |
|
| 8 |
|
|
|
|
|
| |
ID NUMBER
Not more than 14m (46 ft)
| 5 |
|
|
| |
4 |
| 67 |
|
|
|
23 |
| 8 |
|
|
|
1 | 0 | 9 |
|
|
|
ID NUMBER | TO H/U | REMOTE | RESET | ||
"1" – "7" | 4 | 5 | 6 |
3 |
| 7 | |
| 8 | ||
2 |
| ||
1 | 0 | 9 | |
|
|
ID NUMBER
4English