DSP Setup
X’Over Setting
Fine adjusting the following setting values corresponding to the X’Over values set in the section <Speaker Setting> (page 40).
Display | Item | Range |
| |||
“X’Over” |
|
|
|
|
| |
| “Front” | “FC” | Front High Pass Filter |
| ||
|
|
| Through, 30, 40, 50, 60, 70, 80, 90, | |||
|
|
| 100, 120, 150, 180, 220, 250 (Hz) | |||
|
| “SLOPE” | Front High Pass Slope | |||
|
|
| ||||
| “Rear” | “FC” | Rear High Pass Filter |
| ||
|
|
| Through, 30, 40, 50, 60, 70, 80, 90, | |||
|
|
| 100, 120, 150, 180, 220, 250 (Hz) | |||
|
| “SLOPE” | Rear High Pass Slope |
| ||
|
|
| ||||
| “SubWoofer” | “FC” | Subwoofer Low Pass Filter | |||
|
|
| 30, 40, 50, 60, 70, 80, 90, 100, 120, | |||
|
|
| 150, 180, 220, 250*, Through (Hz) | |||
|
| “SLOPE” | Subwoofer Slope |
| ||
|
|
| ||||
|
| “PHASE” | Subwoofer Phase |
| ||
|
|
| Reverse (180°)/ Normal (0°) | |||
|
|
| ( |
|
| : Factory setting) |
1Select the source
Press the [SRC] button. Turn the [VOL] knob and press it when the desired item is displayed. Select a source other than “STANDBY”.
✍✍SRC Select mode 2: Pressing the [SRC] button repeatedly switches source.
2Enter Audio Control mode Press the [VOL] knob.
3Enter X’Over setting mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “X’Over”.
4Select the speaker you want to set
Turn the [VOL] knob and press it when the desired item is displayed.
Select “Front”, “Rear”, or “SubWoofer”.
5Select the item you want to set
Operation type | Operation |
Selects the item. | Turn the [VOL] knob. |
Adjust each item. | Press the [4] or [¢] button. |
Set the value | Press the [VOL] button. |
6Repeat steps 3 to 4 to complete the X’Over settings.
7Exit Audio Control mode
42
Press the [MENU] button for at least 1 second, and then press it again briefly.
Audio Preset Memory
Registering the value setup by Sound Control.
1Setup Sound Control
Refer to the following operations to setup the Sound Control.
-Car Type Selection (page 40)
-Speaker Setting (page 40)
-Car Type Fine Adjustments (page 41)
-X’Over Setting (page 42)
-Manual Equalizer Control (page 37)
-Listening Position Selection (page 38)
-Listening Position Fine Adjustments (page 38)
2Enter Audio preset memory mode
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “Detailed Setup” > “Preset” > “Memory”.
3Select the number to put in the memory Turn the [VOL] knob and press it when the desired item is displayed.
Select a preset number.
4Turn the [VOL] knob and press it when the desired item is displayed.
Select “YES”.
“Memory Completed” is displayed.
5Exit Audio Control mode
Press the [MENU] button for at least 1 second, and then press it again briefly.
⁄
•Register 6 patterns of Audio Preset Memory.
•Preset number “1”:
When you press the Reset, all the sources will be the setting value which is registered.
•Preset number “1” and “2”:
The memory cannot be erased by the Reset button.
•This function cannot be registered when the iPod Equalizer set in <Preset Equalizer curve Select> (page 37).