Other operations
English
Menu System
To accommodate a greater number of functions, a function set system has been employed for making settings. Press the MENU button to enter the function set mode and then display the function to make the setting.
1Press the MENU button to enter the function set mode,and the MENU indicator lights.
2Press the 2 or 3 button.
Each time the button is pressed, the adjustment mode will change as follows:
°
”MENU FADER" (Fader)
°5
”MENU HPF-F" (High-pass filter for front output)
°5
”MENU HPF-R" (High-pass filter for rear output)
°5
”MENU LPF-S" (Low-pass filter for subwoofer output)
°5
”MENU SUBW LV" (Subwoofer preout level)
°5
”MENU ANA LV" (Analizer level)*1
°5
”MENU LCD CNT" (LCD contrast level)*2
°5
”MENU PREOUT" (Rear / Front output boost)*3
5
3Press the uor dbutton.
Look at the table to adjust the mode being displayed.
4Press the MENU button to end the function set mode.
*1: It varies according to the volume setting on the centre unit, so set the volume level to normal on the centre unit before adjusting it.
*2: The contrast on the equaliser/spectrum analyser display is not adjustable.
*3: If the sensitivity of the connected amp is high enough to accommodate 4V, set the boost level to "HIGH". Otherwise, set it to "LOW".If it has been set to "HIGH", set the input sensitivity on the amp side to 4V. If it is set lower than 4V, noise may be output.
NOTE
The menu settings cannot be stored in the user memory.
Table of Adjustment Mode
Adjustment | Operation of Control button | ||
mode |
|
| |
(Display) | ubutton | dbutton | |
Fader | Front channel | Rear channel | |
(“FADER”) | emphasized.(F15) | emphasized.(R15) | |
|
|
| |
| You can select the frequency to be cut, as | ||
filter for front | follows: |
| |
output | OFF (through) ↔ 40Hz ↔ 60Hz ↔ 80Hz ↔ | ||
| 100Hz ↔ 120Hz ↔ 150Hz ↔ 180Hz ↔ 220Hz | ||
|
| ||
You can select the frequency to be cut, as | |||
filter for rear | follows: |
| |
output | OFF (through) ↔ 40Hz ↔ 60Hz ↔ 80Hz ↔ | ||
| 100Hz ↔ 120Hz ↔ 150Hz ↔ 180Hz ↔ 220Hz | ||
|
|
| |
| You can select the frequency to be cut, as | ||
filter for | |||
subwoofer | follows: |
| |
output | 50Hz ↔ 80Hz ↔ 120Hz ↔ OFF (through) | ||
|
|
| |
|
|
| |
Subwoofer | The subwoofer | The subwoofer sound | |
Preout Level | |||
sound is increased. | is decreased. | ||
|
| ||
|
|
| |
Analizer | The spectrum | The spectrum analyzer | |
level*1 | analyzer level | ||
(“ANA LV”) | increased. | level decreased. | |
| |||
|
|
| |
LCD contrast | The setting values | The setting values | |
level*2 | |||
(“LCD CNT”) | higher. | lower. | |
|
| ||
|
|
| |
Rear / Front |
|
| |
output boost*3 | Boost on.(“HIGH”) ↔ Boost off.(“LOW”) | ||
(“PREOUT”) |
|
| |
|
|
| |
— 6 —