12
display
For your safety the mixer is fitted with 5 separate safety sensors which will operate when using the mixer in the
cooking mode. If the mixer is switched on and a safety sensor activated, the timer/temperature display will show
an errormessage e.g. ‘E:01’. This will be accompanied by a beeping sound and the mixer will not work. Check
the following errormessages:-
If these or any other errorcodes continue to appear on the display contact Kenwood Customer Care.
to use the countdown timer
The timer can be used in both the cooking and non cooking modes. If a countdown time is not selected, the
timer will automatically countup in1 second intervals whilst the mixer is in operation. The maximum running time
is 3 hours.
1 Connect the mixer to the power supply. The display will briefly show and then clear leaving the power on
indicator visible .
2 Press either the+ or – button and 0:00 will appear in the display.
3 Press either the + or – button until the desired time is displayed. The timer will count up in 5 second intervals. If
the button is pressedcontinuously the numbers will change more quickly the longer it is held down. A maximum
time of 3 hours can be set.
Note: If the + button is pressedwhen the timer is at 3:00 the displayed time will change to 0:00. If the – button is
pressedwhen the timer is at 0:00 the displayed time will change to 3:00.
4 Turn the speed control to the desired speed, the mixer will start and the timer will count down in 1 second
intervals.
●The mixer operation can be paused at any time by turning the speed control to the off‘O’ position. This will also
pause the timer.The timer will continue to count down when the mixer is re-started.
5 The mixing process will automatically stop when the total time has elapsed and audible beeps will be emitted for
3 seconds. The display will flash for 5 seconds and then clear showing the power on indicator .
to reset the timer
1 Zero the timer by pressing the + and – buttonsat the same time (the speed control must be in the off ‘O’ position).
●If the machine has been idle for 10 minutes, the LCD display and backlight will enter ‘sleep mode’ and all the
displays will turn off. If any button or controlknob is activated, the display will resume its previous format.
Error Message Description Solution
The head of the machine is in the raised position. Closethe head. Turn the speed control
When the head is lifted, a safety sensor disables to the ‘O’ position and then select the
E:01 the motor and heater.If the speed control is desiredspeed.
turned to any setting other than the Off ‘O’
position when the head is raised, this message
is displayed and the motor will not switch on.
The Cooking Chef Bowl is not fitted. The heating Ensure that the Cooking Chef bowl is
function will only work if the Cooking bowl is being used. Check that the bowl
E:02 being used. This bowl must also be correctly isfitted correctly.Turn the speed
fitted. Safety sensors will detect an incorrect controlto “0” and then select desired
bowl or the correctbowl incorrectly fitted. speed.
The heat shield is not fitted. The heating function Ensure the heat shield is fitted
E:03 will be disabled if the heat shield is not correctly correctly.Turn the speed control to ‘O’
fitted. and then select desiredspeed.
The slow speed outlet and high speed/medium Ensure that all covers are fitted correctly.
speed outlet covers arenot fitted. These covers Turn the speed control to ‘O’ and then
arefitted with safety sensors. If the covers are select desired speed.
E:04 not fitted correctlythe heating will switch off and
if stir functions areselected, the motor will run
continuously.Mixing speeds min to max will
run continuously.
Temperaturesensor problem. If the heater Turn the speed control to ‘O’, unplug the
controldetects a bowl temperature higher than machineand allow to cool. Check
E:09 expected during normal use, the motor and that the bowl base and temperature
heater will automatically switch off. sensors areclean. Replace plug and
switch on as normal.
Motor speed or overheat problem.If the motor Turnthe speed control to ‘O’ and unplug
E:10 stalls or gets too hot, the controlsystem will the machine. Remove any obstructions
automatically switch offthe motor and heater. causing the motor to stall. Ensureall
the air vents areclear of obstructions.
Plug in and switch on.