Playing music
14
1 | 2 | 3 | POWER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 | 5 | 6 | 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 | 8 | 9 | +10 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DISK SKIP | 7 | 2 | 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
A/B +100 | AUTO |
| BAND |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 | ¡ | 4 | ¢ |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| P.CALL |
|
|
|
|
|
|
|
|
|
| PRO LOGIC | 3 STEREO |
|
| |
VIDEO1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
TAPE1 | TUNER | CD | PHONO |
| SRS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3D SPEAKERS |
|
|
|
|
|
|
| STEREO | SRS 3D |
|
| |
|
|
|
| STANDBY |
|
|
|
|
|
|
|
|
| INPUT SELECTOR | VOLUME CONTROL | ||
| TAPE2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
VIDEO2 | AV AUX | MUTE | POWER |
|
|
|
|
|
|
|
|
|
|
|
|
| |
MONITOR |
|
|
|
|
|
|
|
|
|
|
| SOURCE |
|
| |||
|
|
|
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | N.B. | DIRECT |
|
|
CENTER |
| LISTEN |
| +10 |
|
|
| ||||||||||
|
| ON/STANDBY |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
MODE |
| MODE |
|
|
|
|
|
|
|
|
| TAPE2 |
|
|
|
| |
|
|
|
|
| AUTO | DIRECT MEMORY |
| BAND DIMMER |
| TUNING | MONITOR | P.CALL |
|
| |||
| LEVEL |
| VOLUME |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SETUP | CONTROL | SOUND | CONTROL |
|
|
|
|
|
|
|
|
|
|
|
| DOWN | UP |
|
|
|
| PHONES |
|
|
|
|
|
|
|
|
|
|
|
|
|
REMOTE CONTROL UNIT
SPEAKERS
1Turn the power ON.
POWER
ON/STANDBY
2Select the SPEAKERS key setting.
SPEAKERS 
SRS
3D SPEAKERS
The SPEAKERS indicator should light up.
STANDBY
3Select the input source.
INPUT SELECTOR
4Play the selected source.
5Adjust the volume.
VOLUME CONTROL
To decrease |
| To increase |
volume | DOWN | UP volume |
: Keys or controls to be used in this operation
When the SPEAKERS indicator is ON:
The speakers connected to the SPEAKERS terminals on the rear panel output sound.
When the SPEAKERS indicator is OFF:
The speakers do not output sound. Use this setting when listening through headphones.
÷For the operation when the power amplifier
The input sources are switched in the following order:
1TUNER (frequency display) | The selected source is | ||
2PHONO | displayed. | ||
3TAPE1 (MD or VIDEO1)*1 |
|
| |
|
| ||
4CD |
|
| |
C D | |||
5VIDEO2 | |||
|
|
| |
*1: Switching the TAPE1 display to MD or VIDEO1 display
When a KENWOOD MD recorder is connected in the [SL 16] system
control mode, the TAPE 1 input should be switched to the MD input | |||||||
using the following procedure. |
|
|
|
| |||
1Select TAPE1 with the INPUT SELECTOR. |
| ||||||
2Press and hold the AUTO key for more than 2 | Note | ||||||
seconds to select MD. |
|
|
| ||||
|
|
|
| ||||
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
1 TAPE1 |
| 2 MD |
| 3 VIDEO1 |
| ||
|
|
| |||||
|
|
|
|
|
|
|
|
Volume level is displayed.
V O L - 6 8 d B
÷The time taken till the volume level is displayed is variable depending on the current operating condition.
÷Rotating the VOLUME CONTROL at a higher speed increases the amount of volume change (AI VOLUME function).
÷The sound of input source cannot be listened to while TAPE 2 MONITOR is ON.