Preparing for surround sound
20 4Input the distance to the speakers.
Distance to front speakers: | ____ feet____ meters |
Distance to center speaker: | ____ feet____ meters |
Distance to surround speakers: | ____ feet____ meters |
2Use the MULTI CONTROL keys to select the distance to the front speakers.
The speaker indicator to be adjusted blinks.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SP |
| A |
| TI.VOL | L | C | R |
|
|
| FM | DIGITAL |
|
| |||
|
|
|
|
| MUTE |
| LFE | SW |
|
|
| AM PRO LOGIC S.DIRECT |
|
| ||||
|
|
|
|
|
|
|
| MHz 3 STEREO MONITOR |
|
| ||||||||
| RDS |
| EON | PTY | LS |
| S | RS |
|
|
| kHz DOWN MIX | DSP |
|
|
| ||
| TP | TA | NEWS |
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Indication in feet | Indication in meters |
|
|
|
| |||||
•The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments.
3Press the SET UP key to accept the settings.
4Repeat steps 2 and 3 to input the distance for each of the speakers.
5Setup is complete when the input indication reappears.
| SP A | L | R | |
Operations |
|
| SW | |
Display when all speakers have been selected. | ||||
| ||||
• The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input level. The CLIP indicator will blink to indicate the source signal.
CLIP
1Use the INPUT SELECTOR knob to select the source which input level you want to adjust.
•You can store a separate input level for each input source. If the MONITOR function is ON, you can store an input level for when MONITOR is on independently of the input levels for the input sources.
2Press the SOUND key repeatedly until the “INPUT” indication appears.
3Use the MULTI CONTROL keys to adjust the input level.
| SP |
|
|
| TI.VOL |
|
|
| FM | DIGITAL |
|
|
|
| A |
| L | C | R |
|
| ||||
|
|
|
|
| MUTE | LFE |
| SW | AM PRO LOGIC S.DIRECT |
|
| |
|
|
|
|
|
| MHz 3 STEREO MONITOR |
|
| ||||
| RDS |
| EON | PTY | LS | S | RS | kHz DOWN MIX | DSP |
|
| |
| TP | TA | NEWS |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
•The adjustment mode is displayed for approximately eight seconds.
•The input level may be adjusted to any one of three settings: 0dB,
4Press the SOUND key again to return to the input indication.
Normal playback
Preparing for playback
Some preparatory steps are needed before starting playback.
|
|
|
|
|
|
|
|
| INPUT MODE | |||||||||||
ON/STANDBY |
|
|
|
|
|
| AUTO/CINEMA EQ. | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INPUT SELECTOR | ||
V5050D/ | SPEAKERS A/B |
|
V5550D | (SPEAKER/MUTE) | |
|
| |
|
|
|
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/6ch, DVD
be used. | 9 |
Selecting MD/TAPE
Select the source name corresponding to the component connected to the MD/TAPE jacks. The initial factory setting is “TAPE”. To change the source to “MD,” follow the steps below:
1Use the INPUT SELECTOR knob to select “TAPE”.
2Hold down the AUTO/CINEMA EQ. key for more than 2 seconds.
•The source indication changes to “MD”.
•To return to the original indication, repeat procedure 2.
Selecting the speaker system
Press the SPEAKERS A or B key to select the speaker system to be used.
A ON | : Sound from the speakers connected to the SPEAKERS A |
| terminals on the rear panel. |
B ON | : Sound from the speakers connected to the SPEAKERS B |
| terminals on the rear panel. |
A+B ON | : Sound from both the speakers connected to the |
| SPEAKERS A and B terminals on the rear panel. |
A+B OFF : No sound from the speakers. Use this setting when listening
| with headphones for stereo sound in all playback modes. | ||||
The indicator for the speakers | The speaker indicator lights. | ||||
you want to use should be lit. | |||||
SP A B | L | R | SP A B | L | R |
|
| SW |
|
| SW |
| |||||
|
|
| V5550D |
|
|
•Selecting “6ch INPT” by pressing the INPUT MODE key, whereby “DVD/ 6ch” is the input source will cause SPEAKER A to be selected automati- cally.
On the
Turning on the receiver
1Turn on the power to the related components.
2Turn on the power to this receiver by pressing POWER (and ON/ STANDBY) key(s).