Kenwood KRF-X9995D Off, Nml, Nml, Lrg, Lrg, Nml, OFF, Re-Mix, Re-Mix, ON/OFF, Re-Mix, SP Distance, Custom setup:

Remote Setup

Chapter Two : Setting Up PowerTouch

Custom setup: Use this method for a more customized setup where you determine more of the speaker settings, such as the bandwidth of the sound sent to each speaker. Custom setup configures the following: SW=subwoofer, L=front left, R=front right, C=center, SL=surround left, SR=surround right, SBL=surround back left and SBR=surround back right.

1Touch on the Speaker Selection menu:

2Aim PowerTouch at the receiver and touch the speaker

38	button until the correct setting appears (see below).
	The front left and right buttons, the surround left
	and right buttons and the surround back left and
	right buttons are linked; if you touch one, you change
	the settings for both.

•Off means you are not using the speaker. (Not avail- able for front speakers). If no subwoofer is connected, all bass below 80Hz is sent to front left and right speakers.

•On means that you are using the speaker. (Only avail- able for subwoofer).

•Select Nml (= Normal/THX) if the speaker is not ca- pable of producing clean, deep bass energy at output levels that match those produced by a typical powered subwoofer. All bass below 80Hz in that channel is re- moved from that speaker and is sent to the subwoofer (or sent to the front speakers if subwoofer is set to off) in all listening modes. Most speakers should be consid- ered Nml. If no subwoofer is connected, that signal is sent to front left and right speakers.

If you have THX certified speakers, select the Nml set- ting.

•Select Lrg (= Large) if the speaker is capable of pro- ducing clean, deep bass energy at output levels that match those produced by a typical powered subwoofer. All bass below 80Hz in that channel is left in that speaker in all listening modes.

The subwoofer may not output audio depending on the setups of the input signal, speakers and listen mode.

3If you set your left and right front speakers to Lrg and want to send bass to the subwoofer in all Listen

modes, touch until “On” appears above the button. SW Re-Mixmixes some of the bass compo- nents in the signals for all the speakers and output it to the subwoofer.

The SW Re-Mix ON/OFF is defeated when you set your front speakers to Nml.

4Touch to save your settings.

5Touch to move to the next speaker setting or

touch to return to the Setup Surround menu.

When activating the THX operation, it is recommended to set SW Re-Mix OFF so that the THX operation can match correctly the human sense of audition.

Speaker combinations that can be selected with Custom Setup

Subwoofer	Front	Center	Surround	Surround back
	speakers	speaker	speakers	speakers
			Nml	Nml
	Nml	Nml		Off
		Off	Off	Off
On
		Nml	Nml	Nml
				Lrg
	Lrg		Lrg
		Lrg		Off
		Off
			Off	Off
		Nml	Nml	Nml
				Lrg
		Lrg �	Lrg	Off
Off	Lrg	Off	Off	Off
		Nml	Nml	Nml
				Lrg
			Lrg
		Lrg		Off
		Off
			Off	Off

SP Distance

1.Measure the distance from each speaker to the seat you most often use and note it below:

Speaker Distance (ft or m)

Front left

Center

Front right

Surround right

Surround back right

Surround back left

Surround left

Subwoofer

2.If you are not already there, touch on the Setup Surround menu to open the Speaker Distance menu:

3.Touch or to set the distance for the front left speaker.

4.Touch or to select the next speaker.

5.Repeat steps 3 and 4 for each speaker.

6.Touch to move to the next speaker setting or touch to return to the Setup Surround menu.

Nml : Normal/THX Lrg : Large Off : Do not use.