Kenwood TS-990S manual Firmware updates by USB, DATA mode supported by external I/O switching

HF/50MHz TRANSCEIVER TS-990S Useful functions

Conveniently located interference elimination controls of the sub-receiver

The dedicated sub-receiver has extensive interfer- ence elimination capability and is conveniently located to the right side of the main panel. Access the knobs and keys you need without hesitation. Share the use of main and sub band variable encod- ers by switching the operations object. An LED is lit when operating the sub band to prevent accidental operation (this can also be dedicated to the main encoder variable bandwidth). Other functions have been significantly upgraded in the TS-990S from the TS-590S, including band elimination filters, APF, mute, the addition of slope switching in the DSP IF FILTER, independent AGC OFF key, and simultaneous use of NB1/NB2.

Sub-receiver with extensive interference elimination controls centered on the right side of the main panel.

Useful functions positioned around the main and sub band knob

Frequently used functions are centrally placed in the immediate vicinity of the main and sub band knob. Supporting quick operation for radio sporting.

FIL/SEL:

Preset the bandpass with 2 or 3 widths of the DSP IF filter for quick WIDE/NAR switching operations.

CW T (CW Tune):

Automatic tuning makes the target signal turn into pitch frequency at a press of the CW signal key.

FINE:

The frequency change unit of the tuning knob can be set to 1/10 of the original unit

VOICE:

The PF key is usually for voice trans- mission, but you can also assign a different function to it.

LOCK:

F. LOCK Key. Useful when used in combination with TF-SET.

Increased user-friendliness by placing two USB ports on the front panel

We equipped the front panel with two USB ports, a key jack, microphone jack and a headphone jack. Use USB memory or

a keyboard.

Firmware updates by USB

Switch to update mode and insert USB memory into the USB-A port on the front panel, and the update will automatically begin. Or access your USB mem- ory from your PC by connecting your PC via USB cable to the USB-B port on the rear panel, switch to update mode, and a folder named TS-990 will appear on your computer.

DATA mode supported by external I/O switching

There are a variety of I/O interfaces, including the microphone jack, analog audio input and output, USB audio interface, and optical digital interface. By combining DATA mode (1-3) with SSB/FM/AM modes, it is possible to easily switch between an external device for modulation and demodulation. Switch between DATA VOX function and mute for each modulated line.

Transmit and receive

DSP equalizers

In addition to the legacy presets, up to a maximum of three user settings can be configured. You can store the equalizer settings used for each mode and enjoy a very comfortable

rag-chew session with others.

RX equalizer

Voice guidance / recording function

Equipped with voice guidance for frequencies, key control, and setting. You can also record and replay your message.

Remote control

the TS-990S from your PC

Using the ARCP-990 software (radio control soft- ware), you can control most functions from your PC. Control the memory channel, settings, and functions using your PC.

Download the free software from the Kenwood website.

ARCP-990 example views

Kenwood SKY COMMAND SYSTEM II

Enables full-duplex operation with improved functionality such as visual confirmation of HF frequency on the LCD panel. Control via TNC (AX.25) enables more access to HF functions: XIT, mode switching, split-frequency operations on/off, memory shift, and frequency step selection. The transporter sends out its pre-programmed call sign via CW every 10 minutes.

Commander	Transporter
			HF antenna
		COM
		connector
		MIC
		ø3.5 mm EXT SP
Commander	Transporter		HF Transceiver
TH-D72A/ TM-D710A	TH-D72A / TM-D710A		TS-990S
440 MHz/144 MHz	440 MHz/144 MHz

440 MHz band

Voice signals, Control signals

440 MHz band	144 MHz band
Confirmation of HF frequency	HF receive audio

*Kenwood SKY COMMAND SYSTEM II uses a pair of TH-D72A/TM-D710A transceivers.

TS-990S is limited to the following functions in the operation of the current KSS. Operation Commander [A / B] in the TS-990S is equivalent to [M / S].

Memory channel is simplex operation only.

Remote power On/Off is not available on Standby State Low Power Consumption mode.

Control to the main band operation only.

Note: Refer to applicable Amateur Radio regulations to check whether you are permitted to use this function.

13