General features

Function of the KDC-X7533U

Adjusting the detail of Audio Control

Among the Basic Audio items, you can adjust the Bass level, Middle level, and Treble level in detail.

1Select the Basic Audio item

Select the desired item to be set in detail from followings;

•Bass level

•Middle level

•Treble level

For how to select Basic Audio items, see <Audio Control> (page 11).

2Enter Detail adjustment mode of Audio ControlPress the [VOL] knob for at least 1 second.3Select the Detail Audio item to adjust Press the [VOL] knob.

Each time you press the knob, the item to be adjusted alternates between the items shown in the table below.

4Adjust the Detail Audio item Turn the [VOL] knob.Bass level

Adjustment Item

Display

Range

Bass Center Frequency

"BAS F"

40/50/60/70/80/100/

 

 

120/150 Hz

Bass Q Factor

"BAS Q"

1.00/1.25/1.50/2.00

Bass Extend

"B EX"

OFF/ON

Middle level

 

 

Adjustment Item

Display

Range

Middle Center Frequency

"MID F"

0.5/1.0/1.5/2.0 kHz

Middle Q Factor

"MID Q"

1.0/2.0

Treble level

 

 

Adjustment Item

Display

Range

Treble Center Frequency

"TRE"

10.0/12.5/15.0/17.5 kHz

5Exit the Detail Audio Control mode Press the [VOL] knob for at least 1 second.

•When you set the Bass Extend to ON, low frequency response is extended by 20%.

•You can exit the Audio Control mode at anytime by pressing any button except for [VOL] and [ATT] buttons.

Audio Setup

Setting the Sound system, such as Cross over Network.

1Select the source to adjust Press the [SRC] button.

2Enter Audio Setup modePress the [VOL] knob for at least 1 second.3Select the Audio Setup item to adjust Press the [VOL] knob.

Each time you press the knob, the item to be adjusted alternates between the items shown in the table below.

4Setup the Audio item Turn the [VOL] knob.

Adjustment Item

Display

Range

Front High Pass

"HPF"

Through/40/60/80/100/120/

Filter*1,3

 

150/180/220 Hz

Rear High Pass Filter*1,3

"HPR"

Through/40/60/80/100/120/

 

 

150/180/220 Hz

Low Pass Filter*1,2,3

"LPF"

50/60/80/100/120/Through

 

 

Hz

Subwoofer Phase*1,2,3,4

"PHAS"

Reverse (180°)/ Normal (0°)

Volume offset

"V-OFF"

–8 — ±0

Loudness

"LOUD"

OFF/ON

Dual Zone System*1

"2ZON"

OFF/ON

•Volume offset: Sets each source’s volume as a difference from the basic volume.

•Loudness: Compensates for low and high tones during low volume.

•*1 Function of the KDC-X7533U.

•*2 You can control this item when <Subwoofer Output> (page 13) is set to "SW ON".

•*3 You can control this item when "2ZON" of <Audio Setup> (page 12) is set to "OFF".

•*4 You can control this item when Low Pass Filter is not set to Through.

•Dual Zone System

Main source and sub source (Auxiliary input) output Front channel and Rear channel separately.

-Set up the channel of sub source by <Dual Zone System Setting> (page 29).

-Select Main source by [SRC] button.

-Adjust the volume of Front channel by [VOL] knob.

-Adjust the volume of Rear channel by <Audio Control> (page 11).

-The Audio Control has no effect on sub source.

12 English