The messages shown below display your systems condition.

EJECT:

No disc magazine has been loaded in

 

the changer. The disc magazine is not

 

completely loaded.

 

➪ Load the disc magazine properly.

 

No CD in the unit.

 

➪ Insert the CD.

NO DISC:

No disc has been loaded in the disc

 

magazine.

 

➪ Load a disc into the disc magazine.

TOC ERR:

No disc has been loaded in the disc

 

magazine.

 

➪ Load a disc into the disc magazine.

 

The CD is quite dirty. The CD is upside-

 

down. The CD is scratched a lot.

 

➪ Clean the CD and load it correctly.

READ ERR:

• The number of files or folders which are

 

stored in the connected USB device is

 

above the limitation.

 

• The file system of the connected USB

 

device is broken.

 

➪ Copy the files and folders for the

 

USB device again referring to www.

 

kenwood.mediamanager.jp. If the error

 

message is still displayed, initialize the

 

USB device or use other USB devices.

E-05:

The CD is upside-down.

 

➪ Load the CD correctly.

BLANK:

Nothing has been recorded on the MD.

NO TRACK:

No tracks are recorded on the MD,

 

although it has a title.

NO PANEL:

The faceplate of the slave unit being

 

connected to this unit has been removed.

 

➪ Replace it.

E-77:

The unit is malfunctioning for some reason.

 

➪ Press the reset button on the unit. If the

 

"E-77" code does not disappear, consult

 

your nearest service center.

E-99:

Something is wrong with the disc

 

magazine. Or the unit is malfunctioning for

 

some reason.

 

➪ Check the disc magazine. And then

 

press the reset button on the unit. If the

 

"E-99" code does not disappear, consult

 

your nearest service center.

LOAD:

Discs are being exchanged in the Disc

 

changer.

READING:

The unit is reading the data on the disc.

HOLD:

The protective circuit in the unit activates

 

when the temperature inside the

 

automatic disc changer exceeds 60°C

 

(140°F), stopping all operation.

 

➪ Cool down the unit by opening

 

the windows or turning on the air

 

conditioner. As the temperature falls

 

below 60°C (140°F), the disc will start

 

playing again.

IN (Blink):

The CD player section is not operating

 

properly.

 

➪ Reinsert the CD. If the CD cannot be

 

ejected or the display continues to flash

 

even when the CD has been properly

 

reinserted, please switch off the power

 

and consult your nearest service center.

PROTECT:

The speaker wire has a short-circuit or

 

touches the chassis of the vehicle, and

 

then the protection function is activated.

 

➪ Wire or insulate the speaker cable

 

properly and press the reset button.

NA FILE:

An Audio file is played with a format that

 

this unit can’t support.

 

➪ ----

COPY PRO:

A copy-protected file is played.

 

➪ ----

NO DVICE:

The USB device is selected as a source

 

although no USB device is connected.

 

➪ Change the source to any source other

 

than USB. Connect an USB device, and

 

change the source to USB again.

NA DVICE:

An unsupported USB device is connected.

 

➪ For the supported USB devices, refer to

 

<About USB device> (page 7).

NO MUSIC/ E-15:

•Media was played that doesn’t have data recorded that the unit can play.

•The connected USB device contains no playable audio file.

➪Use media that has data recorded that the unit can play.

USB ERR:

The connected USB device is rated a

 

current capacity higher than the allowable

 

limit.

 

➪ Check the USB device with reference to

 

<About USB device> (page 7).

 

Some trouble may have occurred to the

 

connected USB device.

 

➪ Remove the USB device and then

 

reconnect it. When the same message

 

displays again, use another USB device.

English 43