In case of difficulty

67

 

 

 

 

 

 

 

 

 

 

 

 

 

XD-SERIES (EN/M,T)

 

 

 

 

 

 

 

 

 

 

 

Sound is distorted.

÷ The tape being played was recorded

÷ Try another tape.

 

 

 

 

 

 

 

with distorted sound.

 

 

 

 

 

 

 

 

÷ A tape which has been recorded with

÷ Switch off the equalizer and 3D W

 

 

 

 

the equalizer and/or 3D surround

surround effects before starting E

 

 

 

 

effects is being played back by

playback.

 

 

 

 

 

 

 

applying the equalizer effect.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sound from the MD/DVD

÷ The input level is too high.

÷ Decrease the input level.

Q

 

 

 

INPUT (external input) is

 

 

 

 

 

 

 

 

distorted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Noise is noticeable.

÷ The tape head is magnetized.

÷ Demagnetize the head referring to

 

 

 

 

 

 

“Maintenance”.

 

 

 

 

 

 

 

÷ External noise is induced.

÷ Install the system at a distance from

 

 

 

 

 

 

 

 

other electric appliances and TV.

 

 

 

 

 

 

 

÷ A tape which has been recorded with

÷ Switch on the Tape Equalizer or Dolby

 

 

 

 

 

Dolby NR is being played back with-

NR.

 

 

 

 

out switching the Tape Equalizer or

 

 

 

 

 

 

 

 

Dolby NR on.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sound vibrates.

÷ The capstans or pinch rollers are dirty.

÷ Clean the head referring to “Mainte-

 

 

 

 

 

 

nance”.

 

 

 

 

 

 

 

÷ The tape is wound irregularly.

÷ Wind the tape again by fast forward-

 

 

 

 

 

 

ing, rewinding or playing from an end

 

 

 

 

 

 

 

 

to the other.

 

 

 

 

 

 

 

 

 

 

 

 

 

Recording cannot be started

÷ The recording protect tab of the cas-

÷ Use a cassette with an unbroken re- ¡

 

 

 

 

by pressing the record key.

sette has been broken.

cording protect tab or block the hole.

 

 

 

 

 

 

 

÷ The cassette holder is not closed com-

÷ Close the holder completely.

§

 

 

 

 

 

pletely.

÷ Select the source to be recorded with

·

 

 

 

 

 

÷ The TAPE input is selected.

 

 

 

 

 

the input selector key.

 

 

 

 

 

 

 

÷ The tape is fully wound to one of the

÷ Change the tape transport direction of

¤

 

 

 

 

 

reels.

deck B or reverse the tape insertion

 

 

 

 

 

 

 

 

orientation.

 

 

 

 

 

 

(XD-6...series, XD-8...series

÷ The DSP play or surround play pattern

÷ Select other equalizer pattern than E

 

 

 

only)

is selected.

the DSP play and surround play pat-

 

 

 

 

 

 

 

 

terns.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CD player

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Symptom

Cause

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A CD is placed in the player

÷ The disc is placed upside down.

÷ Place the disc properly, with the label

¢

 

 

 

 

but it cannot be played.

 

side facing upward.

 

 

 

 

 

 

 

÷ The disc position is displaced.

÷ Place the disc properly.

¢

 

 

 

 

 

÷ The disc is extremely dirty.

÷ Clean the disc referring to “Handling ¡

 

 

 

 

 

of discs and tapes”.

 

 

 

 

 

 

 

÷ The disc is scratched.

÷ Try another disc.

 

 

 

 

 

 

 

÷ Dew is condensed on the optics lens.

÷ Refer to “Caution on condensation”

 

 

 

 

 

and remove the condensation by

 

 

 

 

 

 

 

 

evaporation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sound is not produced.

÷ The disc has not been placed.

÷ Place a disc in the CD player.

¢

 

 

Knowledge

 

 

÷ The player is not put to the play mode.

of discs and tapes”.

¢

 

 

 

 

÷ Press the play key.

 

 

 

 

 

÷ The disc is extremely dirty.

÷ Clean the disc referring to “Handling ¡

 

 

 

 

 

÷ The disc is scratched.

÷ Try another disc.

 

 

 

section

 

 

 

 

 

 

Sound skips.

÷ The disc is dirty.

÷ Clean the disc referring to “Handling ¡

 

 

 

 

of discs and tapes”.

 

 

 

 

 

 

 

÷ The disc is scratched.

÷ Try another disc.

 

 

 

 

 

 

 

÷ The player is subject to vibration.

÷ Install the unit in a place not subject to

 

 

 

 

 

 

 

 

vibrations.