6 English
Bch Ach
INPUT
SENSITIVITY(V)
INPUT
SENSITIVITY(V)
HPF
FREQUENCY(Hz)
HPF
FREQUENCY(Hz)
LPF
FREQUENCY(Hz)
4
0.2(MAX)(MIN)5
3
2
1
0.5
0.3
4
0.2(MAX)(MIN)5
3
2
1
0.5
0.3
50 200
50 200
150
100
70
50 200
150
100
70
150
100
70
FILTER
HPF
LPF
OFF
AMPCONT
ON
OFF
ISF
ON
OFF
HPF
ON
OFF
OPERATION
MONO(Lch)
STEREO
OPERATION
MONO(Lch)
STEREO
HPFOPERATION LPFOPERATION
50Hz
70Hz
100Hz
150Hz
200Hz
30
-20
-16
-12
-8
-4
0
50100200 400 1K(Hz) 30
-20
-16
-12
-8
-4
0
50100200 400 1K(Hz)
VOLTFAN
CURRTEMP
Display mode
You can set up the display items as follows:
1 Enter Menu mode
Press the [MENU] button.
"VOLT"/"CURR"/"TEMP"/"FAN" is displayed.
2 Select a display item
Press the [2] or [3] button.
The display items are switched in the following sequence.
Display Information
"VOLT" Indicates the source voltage (V).
"CURR" Indicates the current consumption (A).
"TEMP" Indicates the internal temperature (°F/°C).
"FAN" Indicates the rotation speed of the cooling fan in 3 steps: "FAST", "SLOW" or "OFF".
3 Exit Menu mode
Press the [MENU] button for at least 1 second.
NOTE
When the internal temperature is -22°F/-30°C or less, "-22F"/"-30C" is
displayed.
Separate Amp Control
The following explains how to control the sound of amplifier B using the
Amplifier Control of the unit.
1 Enter Menu mode
Press the [MENU] button.
2 Select the Menu item
Press the [MENU] button.
The setup items are displayed approximately 1 second first, then the set
values are displayed.
3 Adjust the Menu item
Press the [2] or [3] button.
The setup items and set values are switched as follows.
Display Range Adjustment Item
"VOLT"/"CURR"/"TEMP"/"FAN" For the operation method refer to <Display mode>
"BASS" 60/80/100/200 (Hz) Bass Center Frequency
"BA G" B–15 — B+15 (dB) Bass level
"BA Q" Q1.00/Q1.25/Q1.50/Q2.00 Bass Q Factor
"EXT" ON/OFF When the bass extend is set to ON, low frequency response is
extended by 20%.
"TREB" 10/12/15/17 (kHz) Treble Center Frequency
"TR G" T–15 — T+15 (dB) Treble level
"VOL" –20 — 0 (dB) Volume offset
"TEMP" FAHR (Fahrenheit) or
CELS (Centigrade)
The Fahrenheit or Centigrade temperature unit can be selected
for the Display mode.
"DEFA" For the operation method refer to <Default>
"AMP" 0 — 7 The ID Number you have assigned is displayed.
4 Exit Menu mode
Press the [MENU] button for at least 1 second.
NOTE
When you hold down the [3] button 3 or more seconds during ID number
display ("AMP"), message "MEMO" is displayed and you can register the values
you have set with the Amplifier Control. To call the Amplifier Control’s values,
hold down the [2] button 3 or more seconds during ID number display
("AMP"). Then, you can recall the value when message "LOAD" is displayed.
Default
Resets all values you have set to the initial (default) values.
1 Enter Menu mode
Press the [MENU] button.
2 Select Default mode
Press the [MENU] button.
Select the "DEFA" display.
3 Resets the value to its default
Press the [3] button for at least 2 seconds.
Message "----" is displayed, and the value is initialized.
4 Exit Menu mode
Press the [MENU] button for at least 1 second.
NOTE
Volume offset value can not be initialized.
Display Demonstration
The "VOLT"/"CURR"/"TEMP"/"FAN" items are displayed repeatedly.
Press the [MENU] button for at least 2 seconds.
The indicator flashes in the Demonstration mode.
Canceling the Demonstration mode
Press any button to cancel the Demonstration mode.
MENU
2 / 3
Indicator
Amplifier Control System